manualshive.com logo in svg

MR OILTAP R, Инструкции по установке и вводу в эксплуатацию

Поделиться
Скачать
MR OILTAP R Скачать руководство пользователя страница 178

8 Commissioning the transformer at the operating site

Maschinenfabrik Reinhausen GmbH 2015

178

4427410/00 EN

OILTAP® R

Bleeding suction pipe on pipe connection S

1.

Remove screw cap from pipe connection S.

Figure 220: Screw cap

2.

NOTICE!

 Open vent screw and bleed suction pipe. Make sure the suc-

tion pipe is fully vented. The insulation capability of the on-load tap-
changer to ground will otherwise be significantly impaired.

3.

Close vent screw.

4.

Seal vent screw with screw cap.

Performing trial tap-change operations

Before energizing the transformer, test tap change operations must be car-
ried out to check the mechanical functions of on-load tap-changer and mo-
tor-drive unit.

NOTICE

 

Damage to the on-load tap-changer!

Damage to the on-load tap-changer by actuating the on-load tap-changer
without oil!
► Before actuating the on-load tap-changer for the first time, the tap se-

lector must be completely immersed in transformer oil and the oil com-
partment completely filled with oil.

► The on-load tap-changer can be operated in the temperature range of

the surrounding transformer oil of between -25 ° and +105 °C and with
overload up to +115 °C in accordance with IEC 60214-1.

1.

NOTICE!

 Make sure that in each operating position the tap position in-

dicators of motor-drive unit and on-load tap-changer (inspection window
in the on-load tap-changer head) read the same position. An incorrectly
coupled motor-drive unit will damage the on-load tap-changer.

8.5.2

8.6

 

Содержание OILTAP R















































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды