MR OILTAP R Скачать руководство пользователя страница 66

Страница: 66 / 206

5 Mounting

Maschinenfabrik Reinhausen GmbH 2015

4427410/00 EN

OILTAP® R

Screw on-load tap-changer head cover using screws and safety ele-
ments.

Figure 60: On-load tap-changer head cover

Drying the on-load tap-changer

Connect pipe connections R and Q of on-load tap-changer head to the
kerosene vapor lead using one shared lead.

Seal off unused pipe connections with a suitable blank cover.

Figure 61: Shared lead

Vapor-phase drying in the transformer tank

Supply kerosene vapor at a temperature of around 90 °C. Keep this
temperature constant for 3 to 4 hours.

Increase the kerosene vapor temperature by approx. 10 °C/hour to the
desired final temperature (125 °C maximum on the on-load tap-chang-
er).

Vacuum dry on-load tap-changer at between 105 °C and maximum 125
°C for at least 50 hours.

Residual pressure of no more than 10

-3

bar.

Closing kerosene drain plug

Remove diverter switch insert.

Close kerosene drain plug with extended socket wrench by turning
clockwise (tightening torque 20 Nm).

5.2.6.2.4

5.2.6.2.5

Содержание OILTAP R















































































































































































































Результаты поиска

Содержание OILTAP R

Отзывы:

Бренды по названию

Популярные бренды

MR OILTAP R, Инструкции по установке и вводу в эксплуатацию

Результаты поиска

Содержание OILTAP R

Отзывы:

Бренды по названию

Популярные бренды