manualshive.com logo in svg

MR OILTAP R, Инструкции по установке и вводу в эксплуатацию

Поделиться
Скачать
MR OILTAP R Скачать руководство пользователя страница 54

5 Mounting

Maschinenfabrik Reinhausen GmbH 2015

54

4427410/00 EN

OILTAP® R

Drying on-load tap-changer in transformer tank

Dry on-load tap-changer using the following instructions to ensure the dielec-
tric values assured by MR on the on-load tap-changer.

If you want to dry the on-load tap-changer in the transformer tank, first com-
plete transformer assembly and then undertake drying.

If drying in the transformer tank, the following methods are possible:
▪

Vacuum-drying

▪

Vapor-phase drying

Vacuum-drying in the transformer tank

Before you start vacuum-drying in the transformer tank, you must place a
connecting lead between the corresponding pipe connections and seal off
the pipe connections not being used with blank covers.

The on-load tap-changer head cover remains closed during the entire drying
process.

1.

Establish a connecting lead either between connections E2 and Q or
connections E2 and R on the on-load tap-changer head.

2.

Seal off unused pipe connections with a suitable blank cover.

Figure 38: Connecting lead

Vacuum-drying in the transformer tank

1.

Heat up the on-load tap-changer in air at atmospheric pressure with a
temperature increase of about 10 °C/h to a final temperature of maxi-
mum 110 °C.

2.

Pre-dry the on-load tap-changer in circulating air at a max. temperature
of 110 °C for a period of 20 hours.

3.

Vacuum dry on-load tap-changer at between 105 °C and maximum 125
°C for at least 50 hours.

4.

Residual pressure of no more than 10

-3

 bar.

5.2.6

5.2.6.1

 

Содержание OILTAP R















































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды