MR OILTAP R Скачать руководство пользователя страница 181 | Manualshive

Страница: 181 / 206

MR OILTAP R Скачать руководство пользователя страница 181

9 Fault elimination

Maschinenfabrik Reinhausen GmbH 2015

181

4427410/00 EN

OILTAP® R

Error pattern

Action

Tripping of protective relay (for example RS)

Also contact MR.

Tripping of pressure relief device (for example
MPreC®)

Remove diverter switch insert following mainte-
nance manual for the relevant on-load tap-changer.
Depending on the cause of tripping, take measure-
ments/carry out checks on the transformer.
Contact MR.

Activation of pressure monitoring device (for exam-
ple DW 2000)

Also contact MR.

Activation of tap-change supervisory control

The motor-drive unit can no longer be electrically
actuated once the tap-change supervisory control
has been activated. Manual operation of the motor-
drive unit via the hand crank when the transformer
is switched on is prohibited.
Remove diverter switch insert following mainte-
nance manual for the relevant on-load tap-changer.
Depending on the cause of tripping, take measure-
ments/carry out checks on the transformer.
Also contact MR.

Activation of rupture disk in on-load tap-changer
head cover

Remove diverter switch insert following mainte-
nance manual for the relevant on-load tap-changer.
Depending on the cause of tripping, take measure-
ments/carry out checks on the transformer.
Also contact MR.

Tripping of motor protective switch in motor-drive
unit

Request "Information sheet on motor protective
switch tripping" from MR, complete and return to
MR.

Tripping of signaling contact that indicates that the
oil has fallen below the minimum oil level in the on-
load tap-changer oil conservator

Check pipework system (pipes etc.) and on-load
tap-changer head for leaks. Check oil level and oil
quality of diverter switch oil in accordance with op-
erating instructions for on-load tap-changer. If the
oil falls below the limit values, also contact MR.

On-load tap-changer not changing tap position
(sluggishness, Raise keys/Lower keys not working,
diverter switch action not audible)

Contact MR.

No change in voltage on transformer despite
change in position on motor-drive unit

Contact MR.

Tap position indicator on motor-drive unit and on-
load tap-changer different

Contact MR.

Noises on drive shaft or motor-drive unit when
changing tap position

Ensure proper mounting of the drive shaft in ac-
cordance with its operating instructions. Check that
hose clips and protective covers are seated cor-
rectly. Contact MR in the event of noise from the
motor-drive unit.

«
...
179
180
181
182
183
...
»

Содержание OILTAP R















































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды