manualshive.com logo in svg

MR OILTAP R, Инструкции по установке и вводу в эксплуатацию

Поделиться
Скачать
MR OILTAP R Скачать руководство пользователя страница 182

9 Fault elimination

Maschinenfabrik Reinhausen GmbH 2015

182

4427410/00 EN

OILTAP® R

Error pattern

Action

Red message on monitoring unit

If possible read out database and send to MR
along with error code.

Warning or tripping of Buchholz relay on transform-
er

Notify manufacturer of transformer.

Deviation from desired value when measuring
winding resistance of transformer

Contact manufacturer of transformer and, if neces-
sary, MR and provide measured values.

Deviation from desired value during dissolved gas
analysis (transformer oil)

Contact manufacturer of transformer and, if neces-
sary, MR and provide measured values.

Deviation from desired value during transformer ra-
tio test

Contact manufacturer of transformer and, if neces-
sary, MR and provide measured values.

Deviation from limit value for diverter switch oil val-
ues

Carry out oil change, check oil conservator breath-
er of on-load tap-changer.

Table 10: Fault elimination

Tripping of the protective relay and re-commissioning the
transformer

 WARNING

Danger of death or severe injury!

Danger of death or severe injury if on-load tap-changer and transformer are
insufficiently tested!
► Be sure to check on-load tap-changer and transformer after the protec-

tive relay has been tripped. The diverter switch insert or selector switch
insert must be removed in order to do this.

► Only use the equipment again when you are sure there is no damage to

the on-load tap-changer or transformer.

When the circuit breakers have been tripped by the protective relay, proceed
as follows:
1.

Establish time of tripping.

2.

Determine operating position of on-load tap-changer.

3.

As a precaution, block the motor-drive unit by tripping the motor protec-
tive switch to prevent the on-load tap-changer being actuated by remote
control.

4.

Check on-load tap-changer head cover. If oil is leaking, shut the oil con-
servator stop valve immediately.

5.

Check whether the flap valve of the protective relay is in the OFF or IN
SERVICE position.

9.1

 

Содержание OILTAP R















































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды