Moxa Technologies OnCell G3111-HSPA series Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 127

background image

OnCell G3111/G3151-HSPA Series

Getting Started

2-3

Connecting the Hardware

This section describes how to connect the OnCell G3111/G3151-HSPA cellular IP gateway to a host PC or serial
device for the first time. We cover topics such as: Wiring Requirements, SIM Installation, Wall and DIN-Rail
Mounting, Connecting the Power, Connecting to the Ethernet, Connecting to a Serial Device, Adjustable Pull
High/Low Resistors for the RS-485 Port, and LED Indicators.

Wiring Requirements

ATTENTION

Safety First!

Be sure to disconnect the power cord before installing and/or wiring your device. The OnCell
G3111/G3151-HSPA should be secured at one location.

Wiring Caution!

Calculate the maximum possible current in each power wire and common wire. Observe all electrical codes
dictating the maximum current allowable for each wire size. If the current goes above the maximum ratings,
the wiring could overheat, causing serious damage to your equipment.

Temperature Caution!

Be careful when handling the device. When plugged in, the device internal components generate heat, and
consequently the casing may feel hot to the touch.

You should also heed the following guidelines:

•

Use separate paths to route wiring for power and devices. If power wiring and device wiring paths must
cross, make sure the wires are perpendicular at the intersection point.

Note:

Do not run signal or communication wiring and power wiring in the same wire conduit. To avoid

interference, wires with different signal characteristics should be routed separately.

•

Use the type of signal transmitted through a wire to determine which wires should be kept separate. The
rule of thumb is that wiring that shares similar electrical characteristics can be bundled together.

•

Keep input wiring and output wiring separate.

•

Where necessary, it is advisable to label the wiring to all devices in the system.

SIM Card Installation

In order to protect the SIM card, the SIM card slot is located inside the OnCell G3111/G3151-HSPA casing. You
will need to unscrew and remove the outer SIM card cover before installing or removing the SIM card.

Follow these steps to remove or install the SIM card:

1.

Remove the screw holding the outer SIM card cover.

2.

Push the outer SIM card cover down to unlock the SIM
card slot.

3.

Rotate it downwards to expose the SIM card slot.

4.

(a) Remove the SIM card from the SIM card slot, or
(b) Insert the SIM card into the SIM card slot.

5.

Reverse the above steps to replace the outer SIM card
cover.

«
...
10
11
12
13
14
...
»

Содержание OnCell G3111-HSPA series
































































































































Отзывы:

Нет отзывов

Похожие инструкции для OnCell G3111-HSPA series

FXO - RECORD NEW GREETING

Бренд: WELLTECH Страницы: 2

Бренд: ICP DAS USA Страницы: 71

Бренд: THOMSON Страницы: 4

Бренд: Anybus Страницы: 2

Бренд: IntesisBox Страницы: 63

Response Analog IO Gateway

Бренд: ETC Страницы: 4

Бренд: RTA Страницы: 81

AirLink GX Series

Бренд: Sierra Wireless Страницы: 2

Бренд: OPW Страницы: 13

Бренд: Comtrend Corporation Страницы: 70

Бренд: Afar Страницы: 75

Бренд: Primus Страницы: 2

Optinet FE408005AA

Бренд: Black Box Страницы: 159

Бренд: WABCO Страницы: 20

Бренд: AMSEC Страницы: 73

ThinPrint TPG-125

Бренд: SEH Страницы: 28

ThinPrint TPG120

Бренд: SEH Страницы: 120

Бренд: RTA Страницы: 58

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды