Moxa Technologies OnCell G3111-HSPA series Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 127

background image

OnCell G3111/G3151-HSPA Series

Cellular Network Settings

6-4

Username:

This is the user ID account.

Password:

This is the user password.

APN:

Before using the GPRS/UMTS/HSDPA also need APN (Access Point Name) must be added as an IP

gateway initialization command. Detailed instructions are shown below.

Connection control

Connect Rule

Disconnect Rule

GPRS

Always on/None

Always on after power on

None

Trunk

Periodically connect/
inactivity time

Periodically connect (based on the connection
interval setting) attempt to connect to
UMTS/HSDPA first then GPRS after powering
on.

Inactivity time is up

Trunk

Remote host fail/
remote host recovered

Remote Ethernet host has failed. The OnCell
G3111/G3151-HSPA will keep pinging the
remote host over the Ethernet every 3 seconds
after powering on. After failing to connect 5
times in a row, the data from the serial device
will be sent through the HSDPA/UMTS first
then GPRS connection.

When the remote
Ethernet host
returns to normal,
data will revert to
being sent over
Ethernet after 5
continuous
successful pings.

Backup

Connection interval (default = 5 min):

The time interval of the periodic connect function.

Ping remote host:

Key in the IP address of the remote host.

SMS Mode

Short Message Service (SMS) is a telecommunications protocol that allows sending “short” (160 characters or
less) text messages. It is available on most digital mobile phones and some personal digital assistants with
built-in wireless capability. Setting Cellular connection method to SMS Mode allows the ability to enable SMS
Tunnel Mode in the Serial Operation. Refer to

Chapter 7, Serial Port Operation Mode Settings

, for detail

configurations

«
...
39
40
41
42
43
...
»

Содержание OnCell G3111-HSPA series
































































































































Отзывы:

Нет отзывов

Похожие инструкции для OnCell G3111-HSPA series

Бренд: D-Link Страницы: 8

Бренд: D-Link Страницы: 12

Бренд: auto maskin Страницы: 13

Бренд: Elpro Technologies Страницы: 164

Бренд: 3onedata Страницы: 5

Бренд: ProSoft Technology Страницы: 154

Бренд: Gree Страницы: 31

Бренд: Geneko Страницы: 158

Бренд: Cisco Страницы: 4

Бренд: HOOC Страницы: 18

Бренд: SICK Страницы: 60

Бренд: UNION Market Страницы: 36

Бренд: Seneca Страницы: 2

Бренд: Davolink Страницы: 105

Бренд: 2Wire Страницы: 4

Бренд: Gigalink Страницы: 45

Бренд: RTA Страницы: 76

Бренд: Net2Phone Страницы: 113

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды