Moxa Technologies OnCell G3111-HSPA series Скачать руководство пользователя страница 39

Страница: 39 / 127

OnCell G3111/G3151-HSPA Series

Cellular Network Settings

6-2

Cellular Settings

From the left navigation panel, click

Network Settings



Cellular Settings

to configure the cellular

operation settings. The various configuration items are described below:

Type:

The OnCell G3111/G3151-HSPA supports 3 types of operation modes. You may choose from GSM (CSD),

GPRS/EDGE/UMTS/HSDPA/HSPA (PSD, 2G/3G), and SMS.

SIM PIN:

This is a pin code that locks the SIM card until you enter the correct code. Use the pin to protect your

account. The default code is set by the Service Provider. Note that a cell phone must be used to change the PIN.

Band:

Setting the value to “Auto” will allow the IP gateway to automatically negotiate with the local operator

and find an appropriate band. Or users can specify a particular band to use.

Additional settings for each of the three modes are described in the following subsections.

GSM (CSD) Connection

PPP Mode

: PPP provides standard PPP dial-out service.

PPPD Mode

: PPPD (PPP Daemon) is used for dial-in services, since it provides PPP services only when

receiving a request from a remote PC.

Destination IP address:
Source IP address:
IP netmask:

These three values on the left will be filled in automatically by the remote side if
it is not specified by the user.

TCP/IP compression (default=Disable)

: The setting of this field depends on whether the remote user’s

application requests compression.

Inactivity time (default=0 ms)

: This field specifies the idle time setting for auto-disconnection. A setting of

0 ms will cause the port to remain connected even if idle.

Link quality report (default=Disable)

: Setting this field to

Enable

allows the OnCell G3111/G3151-HSPA

to check the PPP connection status with a base station that supports link monitoring.

Outgoing PAP ID:

This is the dial-out user ID account.

PAP password:

This is the dial-out user password.

Incoming PAP check (default=None):

This field allows you to configure the method used, if any, to verify

a user’s ID and authorization.

Содержание OnCell G3111-HSPA series































































































































Результаты поиска

Содержание OnCell G3111-HSPA series

Отзывы:

Похожие инструкции для OnCell G3111-HSPA series

Бренды по названию

Популярные бренды

Moxa Technologies OnCell G3111-HSPA series, Руководство пользователя

Результаты поиска

Содержание OnCell G3111-HSPA series

Отзывы:

Похожие инструкции для OnCell G3111-HSPA series

Бренды по названию

Популярные бренды