Moxa Technologies OnCell G3111-HSPA series Скачать руководство пользователя страница 15

Страница: 15 / 127

OnCell G3111/G3151-HSPA Series

Getting Started

2-6

LED Indicators

The LED indicators on the front panel of the OnCell G3111/G3151-HSPA are described in the following table.

Type

Color

LED Function

PWR

Green

Activation of DC Power.

Off

Power is off, or power error condition exists.

READY

Green

Steady on: Software Ready.
Blinking slowly (1 sec): The OnCell has been located by the OnCell Search
Utility.

Red

(Over Green)

Steady on: Booting up, or IP fault.
Blinking rapidly (0.5 sec): IP conflict.
Blinking slowly (1 sec): Cannot get an IP address from the DHCP server.

Off

Booting up or there is no error condition.

GSM/GPRS

Green

GSM is connected.

Amber

GPRS is connected.

Off

GSM/GPRS is disconnected.

UMTS/HSPA

Green

UMTS is connected.

Amber

HSPA is connected.

Off

UMTS/HSPA is disconnected.

TX/RX

Green

The serial port is transmitting data

Amber

The serial port is receiving data.

Off

No data is being transmitted or received through the serial port.

Signal

(3 LEDs)

Green

Number of LEDs indicates cellular connection signal level
(at least 2 LEDs must illuminated for data transmission)

ATTENTION

Troubleshooting with LEDs:

If both GSM/GPRS and UMTS/HSPA LEDs are off after the device is powered on for several minutes, check the
following:
•

Check the PIN code

•

Check the APN information

•

Check username and password

•

Check the antenna connection

•

Make sure cellular provider coverage is available in the current location

Reset Button

Press and hold the

Reset

button for 5 sec to load factory defaults: Use a pointed object, such as a straightened

paper clip or toothpick, to press the reset button. This will cause the Ready LED to blink on and off. The factory
defaults will be loaded once the Ready LED stops blinking (default IP: 192.168.127.254).

Содержание OnCell G3111-HSPA series































































































































Результаты поиска

Содержание OnCell G3111-HSPA series

Отзывы:

Похожие инструкции для OnCell G3111-HSPA series

Бренды по названию

Популярные бренды

Moxa Technologies OnCell G3111-HSPA series, Руководство пользователя

Результаты поиска

Содержание OnCell G3111-HSPA series

Отзывы:

Похожие инструкции для OnCell G3111-HSPA series

Бренды по названию

Популярные бренды