Mitsubishi QD75M1 Скачать руководство пользователя страница 361 | Manualshive

Страница: 361 / 882

background image

9 - 8

MELSEC-Q

9 MAJOR POSITIONING CONTROL

[3] Continuous path control

(1) Continuous path control

(a) The speed is changed without deceleration stop between the

command speed of the positioning data currently being run and the
speed of the positioning data that will be run next.
The speed is not changed if the current speed and the next speed are
equal.

(b) The speed will become the speed used in the previous positioning

operation if the command speed is set to "-1".

(c) Dwell time will be ignored, even if set.
(d) The next positioning No. is executed automatically in operations by

continuous path control (operation pattern "11"). Always terminate the
positioning by setting operation pattern "00" in the last positioning data.
If the operation pattern is set to positioning continue ("01" or "11"), the
operation will continue until operation pattern "00" is found.
If the operation pattern "00" cannot be found, the operation may be
carried out until the positioning data No. 600. If the operation pattern of
the positioning data No. 600 is not terminated, the operation will be
started again from the positioning data No. 1.

(e) The speed switching patterns include the "front-loading speed

switching pattern" in which the speed is changed at the end of the
current positioning side, and the "standard speed switching pattern" in
which the speed is at the start of the next positioning side. (Refer to

"

Pr.19

Speed switching mode".)

Continuous path control

Standard speed switching mode

Front-loading speed switching mode

(f) In the continuous path control, the positioning may be completed

before the set address/movement amount and the current data may be
switched to the "positioning data that will be run next".

This is because a preference is given to the positioning at a command

speed. In actuality, the positioning is completed before the set

address/movement amount by an amount of remaining distance at

speeds less than the command speed. The remaining distance (

)

at speeds less than the command speed is 0

(distance

moved in 3.5ms at a speed at the time of completion of the

positioning).

«
...
359
360
361
362
363
...
»

Содержание QD75M1



















































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для QD75M1

Бренд: J4C Страницы: 4

Бренд: ABB Страницы: 6

Бренд: JDS Uniphase Страницы: 27

Бренд: Danfoss Страницы: 20

Бренд: OEG Страницы: 168

Бренд: Eaton Страницы: 6

Бренд: QUAD Страницы: 17

Бренд: fadini Страницы: 16

Бренд: Lawler Страницы: 5

Бренд: Parker Страницы: 30

Compax3M Series

Бренд: Parker Страницы: 52

Бренд: Parker Страницы: 337

Бренд: Saab Страницы: 4

Бренд: Water Specialist Страницы: 60

Бренд: Watts Страницы: 24

Бренд: Paradox Страницы: 3

Бренд: W.E.ST. Страницы: 34

Бренд: Ltech Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды