Mitsubishi QD75M1 Скачать руководство пользователя страница 132 | Manualshive

Страница: 132 / 882

background image

5 - 45

MELSEC-Q

5 DATA USED FOR POSITIONING CONTROL

2) When the difference between the last command position of the QD75

at the time the servo stop signal turned ON and the present value at
the time the servo stop signal turned OFF is greater than the value
set in the buffer memory for the restart allowable range setting, the
positioning operation is judged as on-standby and cannot be
restarted.

ON

OFF

Operation

Error

Servo OFF

Stopping/Waitting

Last command position

Servo ON

Restart invalid
Restart valid

Axis status

Servo emergency
stop signal

(b) Processing when the servo ON signal changes from OFF to ON.

1) The positioning operation is stopped and restart can be performed

when the difference between the last command position of the QD75
when the servo ON signal went from OFF to ON is lower than the
value set in the buffer memory for restart allowable range setting.

2) When the difference between the last command position of the QD75

at the time the servo ON signal when from ON to OFF and the
present value at the time the servo ON signal went from OFF to ON
is greater than the value set in the buffer memory for the restart
allowable range setting, the positioning operation is judged as on-
standby and cannot be restarted.

Axis status

Servo emergency
stop signal

Stopping

Positioning

Servo OFF

Stopping/Waiting

Stop command

Servo OFF

Waitting

Restart invalid
Restart valid

Servo ON

ON

OFF

Servo ON

Restart invalid

(2) Setting method

When performing restart at the time servo OFF changes to ON, set the restart

allowable range in the following buffer memory.

Setting value buffer memory

address

Axis 1 Axis 2 Axis 3 Axis 4

Item Setting

range

Default value

64
65

214
215

364
365

514
515

Pr.201 Restart allowable range

setting when servo OFF changes
to ON

0, 1 to 163840 (PLS)

0: restart not allowed

0

[Setting example]

A program in which the restart allowable range for axis 1 is set to 10000 PLS
is shown below.

DMOVP K10000 D0

DTOP H0 K64 D0 K1

Restart allowable range (10000 PLS)
is stored in D0, D1.

Data for D0, D1 is stored in buffer
memory 64, 65 of the QD75.

«
...
130
131
132
133
134
...
»

Содержание QD75M1



















































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для QD75M1

Бренд: Valve Concepts Страницы: 15

Бренд: Warner Electric Страницы: 3

Бренд: iCeeO2 Страницы: 7

Бренд: SABAF Страницы: 6

SmartSwitch 6000

Бренд: Cabletron Systems Страницы: 76

Бренд: Eaton Страницы: 2

Бренд: Eaton Страницы: 2

Бренд: Eaton Страницы: 8

Бренд: Salda Страницы: 20

Бренд: Lawler Страницы: 5

Бренд: RAKwireless Страницы: 6

Бренд: RADEMACHER Страницы: 68

Бренд: Daruifuno Страницы: 24

Бренд: Warner Electric Страницы: 4

Бренд: Coris Страницы: 4

MS6-SV-...-D-10V24

Бренд: Festool Страницы: 32

Бренд: SOMFY Страницы: 56

TempMaster M2 Plus Series

Бренд: Mold-Masters Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды