UBC10.241, UBC10.241-N1
U
–
Series
24V, 10A, DC-UPS
May. 2008 / Rev. 1.1 DS-UBC10.241-EN
All parameters are specified at an input voltage of 24V, 10A output load, 25°C ambient and after a 5 minutes run-in time
unless otherwise noted. It is assumed that the input power source can deliver a sufficient output current.
www.pulspower.com Phone +49 89 9278 0 Germany
2/23
I
NDEX
P
AGE
I
NDEX
P
AGE
1.
General Description ............................................1
2.
Short-form Data ..................................................1
3.
Order Numbers....................................................1
4.
Markings ..............................................................1
5.
Input ....................................................................3
6.
Output in Normal Mode .....................................4
7.
Output in Buffer Mode .......................................5
8.
Battery Input .......................................................6
9.
Buffer Time..........................................................7
10.
Efficiency and Power Losses................................8
11.
Functional Diagram.............................................8
12.
Check Wiring and Battery Quality Tests.............9
13.
Relay Contacts and Inhibit Input ......................10
14.
Front Side User Elements ..................................12
15.
Terminals and Wiring........................................13
16.
Reliability ...........................................................13
17.
EMC ................................................................... 14
18.
Environment ..................................................... 15
19.
Protection Features .......................................... 15
20.
Safety ................................................................ 16
21.
Approvals .......................................................... 16
22.
Fulfilled Standards............................................ 16
23.
Used Substances ............................................... 17
24.
Physical Dimensions and Weight ..................... 17
25.
Installation Notes ............................................. 18
26.
Replacement of the battery............................. 19
27.
Accessories ........................................................ 20
28.
Application Notes ............................................. 21
28.1.
Battery Replacement Intervals............... 21
28.2.
Parallel and Serial Use............................ 22
28.3.
Using the Inhibit Input........................... 23
28.4.
Troubleshooting ..................................... 23
I
NTENDED
U
SE
The unit shall only be installed and put into operation by qualified personnel.
This unit is designed for installation in an enclosure and is intended for general use, such as in industrial control,
office, communication, and instrumentation equipment. Do not use this device in aircraft, trains and nuclear
equipment, where malfunctioning of the power supply may cause severe personal injury or threaten human life.
T
ERMINOLOGY AND
A
BREVIATIONS
DC-UPS
Uninterruptible power supply with DC-Input.
Normal mode
Describes a condition where the battery is charged, the input voltage is in range and the output is
loaded within the allowed limits.
Buffer mode
Describes a condition where the input voltage is below the transfer threshold level, the unit is
running on battery (buffering) and the output is loaded within the allowed limits.
Charging mode
Describes a condition where the battery is being charged, the input voltage is in range and the
output is loaded within the allowed limits.
Inhibit mode
Describes a condition where buffering is disabled on purpose by using the inhibit input of the DC-
UPS. (e.g. for service actions, or to save battery capacity)
Buffer time
Same as the term “hold-up time”.
T.b.d.
To be defined, value or description will follow later.
D
ISCLAIMER
The information presented in this document is believed to be accurate and reliable and may change without notice.
Some parts of this unit are patent by PULS (US patent No 091662,063, Des. 424,529, …).
No part of this document may be reproduced or utilized in any form without permission in writing from the publisher.
Содержание 4350127.256
