MGM 100120-3, Руководство по эксплуатации

Страница: 38 / 72

38 / 72 HBC-series V7 LV+MV
Parameter Table continue
Legend: H - choice from discrete values
With respect to possibility of settings is necessary programming controllers
HBC-series range only by PC with operating system Microsoft
( Windows XP , Vista, Windows 7 or Windows 8 ) and USBCOM_4(i) module with s cable CC_11 . In your PC must be installed and run pro-
gram
„
Controller 2
“. Installation instruction is in manual „
Installing and running of program Controller 2
“.
Keep in mind default (company) settings of parameters represent only average values. These values are usable as “starting values” for starting
of system (model) testing. In most cases will be necessary many parameters change and adapt for the best behavior of the controller
- respectively of your model
– by your images and requests.
Note:
When your requests on parameter range or parameter type, or some other features, don´t realize these standard specification,
contact
MGM
COMPRO
company please.
Most of the above parameters is common to all types of controllers and the types of controls. Some specific parameters are for any type - ex-
cept that it is always highlighted in the description of parameters. The settings are also dependent on the specific hardware of a particular type.
parameter range step Bank #1 Bank #2 Bank #3 Bank #4
Default settings Default settings Default settings Default settings
P16
Acceleration (time from 0% to 100%)
0,1 sec. 60 sec. 0,1 0,5 sec. 0,5 sec. 0,5 sec. 0,5 sec.
P17
Acceleration from STOP position
(only for constant rpm mode)
0,1 sec. 60 sec. 0,1 0,5 sec. 0,5 sec. 0,5 sec. 0,5 sec.
P82 Cruise Control ramp 0,1 sec. 60 sec. 0,1 0,5 sec. 0,5 sec. 0,5 sec. 0,5 sec.
P18
Deceleration (time from 100% to 0%)
0 sec. 60 sec. 0,1 0,5 sec 0,5 sec 0,5 sec 0,5 sec
P22 Brake intensity 0% 100% 1% 30% -- -- --
P23
Brake intensity in Neutral position
(in STOP position)
0% 100% 1% 0% -- 30% 30%
P25
Brake Ramp
(time to reach full braking force)
0 sec. 60 sec. 0,1 0,2s 0,2s 0,2s 0,2s
P26
Brake Ramp in Neutral
(time to reach full braking force)
0 sec. 60 sec. 0,1 0,2s 0,2s 0,2s 0,2s
P21 Freewheel H Yes Yes Yes Yes
P38 Control signal lost masking period 0 60 sec. 10 ms 500 ms 500 ms 500 ms 500 ms
P39 Brake intensity when signal is lost 0 100 % 0 0 0 0
P71
BB data-logging period /
real-time Monitoring
10 ms 100 ms H 100 ms 100 ms 100 ms 100 ms
P85 Parameters saved to BB, sets+ H basic basic basic basic
P28 Motor temperature sensor H Not monitored Not monitored Not monitored Not monitored
P29 Battery temperature sensor H Not monitored Not monitored Not monitored Not monitored
P30 Controller temperature limit 25 110
°C 100°C 100°C 100°C 100°C
P31
Motor temperature limit
60 150
°C 90°C 90°C 90°C 90°C
P32 Battery temperature limit 40 70
°C 55°C 55°C 55°C 55°C
P37 Calibration of motor temp. sensor Y/N No No No No
P36 Calibration of battery temp. sensor Y/N No No No No
P88 Throttle
– allowed max. limit
1000 3300 1mV 3200 3200 3200 3200
P89
Throttle
– allowed min. limit
0 1500 1mV 100 100 100 100
P15 Communication Address 1 256 1 1 1 1 1
P27 Speed of CAN bus 125 kbit 1 Mbit/s 125kb 125 kb 125 kb 125 kb 125 kb
P35
Version of CAN bus
H 2.0 2.0 2.0 2.0
P14 Telemetry H off off off off
P91 Baud rate of RS 232 / 485 10 Bd 1 MBd 1 38400 38400 38400 38400
P79 Signal BL-1 H Braking lights
Indication of
incoming discharge
Indication of
incoming discharge
Indication of
incoming discharge
P70
Braking resistors control (activation )
Y/N No No No No
P80
Motor beeping
(on / off) Y/N Yes Yes Yes Yes
P55
PID regulátor - složka P
P56
PID regulátor - složka I
P57
PID regulátor - složka D