MGM 100120-3, Руководство по эксплуатации

Страница: 17 / 72

17 / 72 HBC-series V7 LV+MV
Connector description of driving board DN-B15:
Connector K1 (linked, associated):

Pin 1 : SWITCH -
connected in a safe way (turned on = switch is disconnected
)

Pin 2: SWITCH -
connected in a safe way (turned on = switch is disconnected
)

Pin 3:
auxiliary supply of +14V up to +35V, can be used when it is not possible to use the main (traction) supply for feeding the in-
ner circuits

Pin 4: PWR GND (
power ground
)

Pin 5: GND

Pin 6:
Temperature sensor for Lipol cells (KTY 81-210) / or can be used as a generic analog input
Connector K2A (primary control input):

Pin 1 : DC/DC converter GND (power ground for DC/DC converter system) or isolated ground for optically isolated driving PWM 1

Pin 2: INP_1 control input digital, PWM 1, (also possible isolated) or Analog potentiometer 2, driving voltage 2

Pin 3: + DC/DC converter output voltage of the or input +5V for isolated PWM 1 or
3.3V (potentiometer 2 feed
)
Connector K2B (primary control input):

Pin 4: GND signal ground

Pin 5: INP_2 control input Analog, potentiometer 1 , driving voltage 1 or input digital or PWM 2

Pin 6: +3.3V output (supply of potentiometer 1)
Connector K3 (communication port CAN or RS 485 / general I/O): CAN /
RS 485, can be isolated also

Pin 1 : GND for communication port can be isolated

Pin 2: CAN_H
or line A of RS 485 bus or output OUT_3 (logical, not power output)

Pin 3: CAN_L
or line B of RS 485 bus or input INP_3 (logical
)
Connector K4 (communication port / general I/O):
RS232 TTL, can be also optically coupled

Pin 1 : RX or input INP_4 (logical, or optocoupler input)

Pin 2: GND or minus pole of optocoupler input

Pin 3: TX or output OUT_4 (logical, or optocoupler output )

Pin 4: +5V
external feed of COM ports, if inner feeding is not used (internal feeding for com port also can be isolated)
Connector K5A or K5B (ICS-2):
communication with PC (module USBCOM 3x), outer I2C bus, indication, ….
(assembled is only one or the other)

Pin 1 : BL-1 signal

Pin 2: SDA

Pin 3: SCL

Pin 4:
output
+3.3V

Pin 5: GND

Pin 6: output +5V
Connector K6 (cooling fan 12V and SPI):
(SPI port is available on if indication by LED is not used)

Pin 1 :
–
fan 12V

Pin 2: +
fan
12V

Pin 3: CS-1

Pin 4: MOSI

Pin 5: MISO

Pin 6: SCK
Connector K7A, K7B, K7C (motor sensors):
Either for classic sensors or an encoder.
K7A, K7B K7C

Pin 1 : SENS_A
●
Pin 1 : GND

Pin 2: SENS_B
● Pin 2: SENS_C

Pin 3: SENS_C
● Pin 3: SENS_B

Pin 4: sensor feeding +5V resp. +10V
● Pin 4: SENS_A

Pin 5: GND
● Pin 5:
Temperature sensor of motor KTY 81-210

Pin 6:
Temperature sensor of motor
KTY 81-210
● Pin 6:
sensor feeding
+5V resp. +10V
Connector K8 (auxiliary inputs):
(available only if BEC is not in the controller)

Pin 1 : GND

Pin 2: AUX_4 auxiliary measuring input, e.g. for connection of altimeter etc .

Pin 3: AUX_3 auxiliary measuring input
Jumper J1:
connection of terminating impedance of CAN or RS 485 bus.
(coupler or soldered jumper)

Closed pins = termination impedance for CAN or RS 485 connected

Open pins = termination impedance for CAN or RS 485 disconnected