Mercury Sable 2008 Скачать руководство пользователя страница 97 | Manualshive

Страница: 97 / 328

background image

Press and pull the window switches
to open and close windows.

•

Push down (to the first detent)
and hold the switch to open.

•

Pull up (to the first detent) and
hold the switch to close.

Rear Window Buffeting:

When one or both of the rear windows are

open, the vehicle may demonstrate a wind throb or buffeting noise. This
noise can be alleviated by lowering a front window approximately two to
three inches.

One touch up or down (Driver’s window only)

This feature allows the driver’s window to open or close fully without
holding the control down.

To operate ONE TOUCH DOWN:

•

Press the switch completely down
to the second detent and release
quickly. The window will open
fully. Momentarily press the
switch to any position to stop the
window operation.

If the switch is pressed and held to
the normal close or ONE TOUCH UP position during a ONE TOUCH
DOWN event, the window will stop. If, after 1/2 second the switch is still
held, the window will perform a normal close or ONE TOUCH UP.

To operate ONE TOUCH UP:

•

Pull the switch completely up to
the second detent and release
quickly. The window will close
fully. Momentarily press the
switch to any position to stop the
window operation.

If the switch is pressed and held to
the normal open or ONE TOUCH DOWN position during a ONE TOUCH
UP event, the window will stop. If, after 1/2 second the switch is still
held, the window will perform a normal open or ONE TOUCH DOWN.

AUTO

2008 Sable

(mgo)

Owners Guide (post-2002-fmt)
USA

(fus)

Driver Controls

97

«
...
95
96
97
98
99
...
»

Содержание Sable 2008









































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sable 2008

Бренд: Calira Страницы: 14

Бренд: Toyota Страницы: 529

BLACK STEEL S2560

Бренд: Fab Fours Страницы: 9

Бренд: Alpine Страницы: 8

X-ACT CONTOUR 53491

Бренд: HUSKY LINERS Страницы: 2

Бренд: Volvo Страницы: 19

Бренд: DEFA Страницы: 7

Бренд: Prorack Страницы: 15

Бренд: Toyota Страницы: 35

Бренд: Brodit Страницы: 2

Бренд: Power Fist Страницы: 12

Бренд: EAL Страницы: 7

Бренд: Hama Страницы: 75

Бренд: Saab Страницы: 445

Бренд: Acura Страницы: 2

Бренд: Toyota Страницы: 52

Quattroporte Automatic

Бренд: Maserati Страницы: 272

Бренд: FALCON RIDGE Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды