manualshive.com logo in svg

Mercury Sable 2008, Руководство пользователя

Mercury Sable 2008 предлагает Owner's Manual для загрузки бесплатно. Подробное описание, инструкции по эксплуатации и поддержание автомобиля доступны для скачивания на manualshive.com. Незаменимая помощь в обслуживании вашего автомобиля. ¡Загрузите свой экземпляр прямо сейчас!

Поделиться
Скачать
background image

It is recommended that the negative battery cable terminal be
disconnected from the battery if you plan to store your vehicle for an
extended period of time. This will minimize the discharge of your battery
during storage.

Note: Electrical or electronic accessories or components added to
the vehicle by the dealer or the owner may adversely affect
battery performance and durability.

Batteries normally produce explosive gases which can cause
personal injury. Therefore, do not allow flames, sparks or lighted

substances to come near the battery. When working near the battery,
always shield your face and protect your eyes. Always provide proper
ventilation.

When lifting a plastic-cased battery, excessive pressure on the
end walls could cause acid to flow through the vent caps,

resulting in personal injury and/or damage to the vehicle or battery.
Lift the battery with a battery carrier or with your hands on opposite
corners.

Keep batteries out of reach of children. Batteries contain sulfuric
acid. Avoid contact with skin, eyes or clothing. Shield your eyes

when working near the battery to protect against possible splashing of
acid solution. In case of acid contact with skin or eyes, flush
immediately with water for a minimum of 15 minutes and get prompt
medical attention. If acid is swallowed, call a physician immediately.

Battery posts, terminals and related accessories contain lead and
lead compounds.

Wash hands after handling.

Because your vehicle’s engine is electronically controlled by a computer,
some control conditions are maintained by power from the battery. When
the battery is disconnected or a new battery is installed, the engine must
relearn its idle and fuel trim strategy for optimum driveability and
performance. To begin this process:

1. With the vehicle at a complete stop, set the parking brake.

2. Put the gearshift in P (Park), turn off all accessories and start the
engine.

3. Run the engine until it reaches normal operating temperature.

2008 Sable

(mgo)

Owners Guide (post-2002-fmt)
USA

(fus)

Maintenance and Specifications

291

Содержание Sable 2008









































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sable 2008

Ignition 63-231 Quick Start preview
63-231
Бренд: Ignition Страницы: 1
Uebler F42 Mounting And Operating Instructions preview
F42
Бренд: Uebler Страницы: 18
Cargo Floor CF500 SL-2 Replacement Instructions Manual preview
CF500 SL-2
Бренд: Cargo Floor Страницы: 16
Ford E-Transit 2022 Manual preview
E-Transit 2022
Бренд: Ford Страницы: 22
Atwood Lippert Components LEVELEGS MPD 66385 Manual preview
Lippert Components LEVELEGS MPD 66385
Бренд: Atwood Страницы: 6
BMW 65 41 2 152 528 Installation Instructions Manual preview
65 41 2 152 528
Бренд: BMW Страницы: 21
Thule Kit 2161 Fitting Instructions preview
Kit 2161
Бренд: Thule Страницы: 2
Mercedes-Benz 2016 SLK Operator'S Manual preview
2016 SLK
Бренд: Mercedes-Benz Страницы: 358
E&G Classics 1398-0502-09 Instruction Manual preview
1398-0502-09
Бренд: E&G Classics Страницы: 2
MVG 0845 C Manual preview
0845 C
Бренд: MVG Страницы: 18
Lexus HS 250h Vehicle Dismantling Manual preview
HS 250h
Бренд: Lexus Страницы: 34
Toyota 86 2020 Quick Reference Manual preview
86 2020
Бренд: Toyota Страницы: 32
SNIPER V2 Inox Owner'S Manual preview
V2 Inox
Бренд: SNIPER Страницы: 2
Saab 2000 9-5 2.3 Turbo Ecopower Owner'S Manual preview
2000 9-5 2.3 Turbo Ecopower
Бренд: Saab Страницы: 256
Soundoff Signal nERGY ETSA200R-PA Quick Start Manual preview
nERGY ETSA200R-PA
Бренд: Soundoff Signal Страницы: 3
Truma Mover H SE User Manual preview
Mover H SE
Бренд: Truma Страницы: 10
Axxess OESWC-LAN29H Installation Instructions Manual preview
OESWC-LAN29H
Бренд: Axxess Страницы: 8
Ford TRANSIT 2015 Quick Reference Manual preview
TRANSIT 2015
Бренд: Ford Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды