Mercury Sable 2008 Скачать руководство пользователя страница 171 | Manualshive

Страница: 171 / 328

background image

To reduce the risk of possible serious injury:
Do not stow objects in seat back map pocket (if equipped) or

hang objects off seat back if a child is in the front passenger seat.
Do not place objects underneath the front passenger seat or between
the seat and the center console (if equipped).
Check the “passenger airbag off” or “pass airbag off” indicator lamp for
proper airbag Status.
Failure to follow these instructions may interfere with the front
passenger seat sensing system.

In case there is a problem with the
front passenger sensing system, the
airbag readiness lamp in the
instrument cluster will stay lit.

If the airbag readiness lamp is lit, do the following:

The driver and/or adult passengers should check for any objects that
may be lodged underneath the front passenger seat or cargo interfering
with the seat.

If objects are lodged and/or cargo is interfering with the seat; please take
the following steps to remove the obstruction:

•

Pull the vehicle over.

•

Turn the vehicle off.

•

Driver and/or adult passengers should check for any objects lodged
underneath the front passenger seat or cargo interfering with the seat.

•

Remove the obstruction(s) (if found).

•

Restart the vehicle.

•

Wait at least 2 minutes and verify that the airbag readiness lamp is no
longer illuminated

•

If the airbag readiness lamp remains illuminated, this may or may/not
be a problem due to the front passenger sensing system.

DO NOT attempt to repair or service the system; take your vehicle
immediately to an authorized dealer.

If it is necessary to modify an advanced front airbag system to
accommodate a person with disabilities, contact the Ford Customer
Relationship Center at the phone number shown in the

Customer

Assistance

chapter of this

Owner’s Guide

.

2008 Sable

(mgo)

Owners Guide (post-2002-fmt)
USA

(fus)

Seating and Safety Restraints

171

«
...
169
170
171
172
173
...
»

Содержание Sable 2008









































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sable 2008

Бренд: Lancia Страницы: 191

Бренд: RaceChip Страницы: 12

CB-796IG2-CIGD-R

Бренд: CARRYBOY Страницы: 4

Бренд: GMC Страницы: 428

Бренд: WABCO Страницы: 48

Бренд: Cadillac Страницы: 518

Бренд: Opel Страницы: 141

Бренд: P-Invent Страницы: 4

Бренд: Kia Страницы: 11

Бренд: Saab Страницы: 426

Бренд: Toyota Страницы: 600

Бренд: Jaeger Страницы: 11

Бренд: Sagem Страницы: 10

Бренд: Toyota Страницы: 165

Бренд: v.link Страницы: 12

Бренд: APS Страницы: 3

Бренд: ORA Страницы: 7

MAGIC WATCH MWE-850-4XXL

Бренд: Waeco Страницы: 228

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды