Mercury Sable 2008 Скачать руководство пользователя страница 262

Страница: 262 / 328

4. Check all battery terminals and remove any excessive corrosion before
you attach the battery cables. Ensure that vent caps are tight and level.

5. Turn the heater fan on in both vehicles to protect from any electrical
surges. Turn all other accessories off.

Connecting the jumper cables

1. Connect the positive (+) jumper cable to the positive (+) terminal of
the discharged battery.

Note:

In the illustrations,

lightning bolts

are used to designate the

assisting (boosting) battery.

2. Connect the other end of the positive (+) cable to the positive (+)
terminal of the assisting battery.

–

2008 Sable

(mgo)

Owners Guide (post-2002-fmt)
USA

(fus)

Roadside Emergencies

262

Содержание Sable 2008









































































































































































































































































































































Результаты поиска

Содержание Sable 2008

Отзывы:

Похожие инструкции для Sable 2008

Бренды по названию

Популярные бренды

Mercury Sable 2008, Руководство пользователя

Результаты поиска

Содержание Sable 2008

Отзывы:

Похожие инструкции для Sable 2008

Бренды по названию

Популярные бренды