Mercury Sable 2008 Скачать руководство пользователя страница 126 | Manualshive

Страница: 126 / 328

background image

Autounlock feature

The autounlock feature will unlock all the doors when:

•

the ignition is in the 3 (RUN) position, all the doors are closed, and
the vehicle has been in motion at a speed greater than 12 mph
(20 km/h);

•

the vehicle has then come to a stop and the ignition is turned to the 1
(LOCK) or 2 (ACC) position; and

•

the driver door is opened within 10 minutes of the ignition being
transitioned to the 1 (LOCK) or 2 (ACC) position.

Note:

The doors will not autounlock if the vehicle has been

electronically locked before the driver door is opened.

Deactivating/activating autounlock feature

Your vehicle comes with the autounlock features activated; there are four
methods to enable/disable this feature:

•

Through your authorized dealer,

•

by using a power door unlock/lock sequence,

•

using a keypad procedure, or

•

or by using the instrument cluster message center. Refer to

Message

center

in the

Driver Controls

chapter.

Note:

The autounlock feature can be activated/deactivated

independently of the autolock feature.

Power door lock switch autounlock enable/disable procedure

Before starting, ensure the ignition is in the 1 (LOCK) position and all
vehicle doors are closed. You must complete Steps 1–5 within 30 seconds
or the procedure will have to be repeated. If the procedure needs to be
repeated, wait a minimum of 30 seconds before beginning again.

1. Place the key in the ignition and
turn the ignition to the 3 (RUN)
position.

2. Press the power door unlock
control on the door panel three
times.

3. Turn the ignition from the 3 (RUN) position to the 1 (LOCK) position.

4. Press the power door unlock control on the door panel three times.

5. Turn the ignition back to the 3 (RUN) position. The horn will chirp
one time to confirm programming mode has been entered and is active.

2008 Sable

(mgo)

Owners Guide (post-2002-fmt)
USA

(fus)

Locks and Security

126

«
...
124
125
126
127
128
...
»

Содержание Sable 2008









































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sable 2008

Бренд: RACLET Страницы: 48

Бренд: RACLET Страницы: 31

Бренд: RAM Страницы: 20

21 COVERT Series

Бренд: Code 3 Страницы: 16

Бренд: Phonocar Страницы: 2

BTFREQ PRO BTFMPD3SR

Бренд: Scosche Страницы: 16

Бренд: UAZ Страницы: 90

Бренд: iOttie Страницы: 58

Бренд: CrimeStopper Страницы: 1

Бренд: Gator Страницы: 6

Бренд: SAFARI Страницы: 5

Prime Design OCM-3032

Бренд: Safe Fleet Страницы: 4

Бренд: Phonocar Страницы: 28

Бренд: Hyundai Страницы: 168

Бренд: Edelbrock Страницы: 2

Бренд: Hudson Страницы: 77

Бренд: Safe Fleet Страницы: 28

Бренд: Subaru Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды