Mercury Sable 2008 Скачать руководство пользователя страница 13

Страница: 13 / 328

Low fuel (if equipped):

Illuminates when the fuel level in
the fuel tank is at or near empty
(refer to

Fuel gauge

in this

chapter).

Speed control:

Illuminates when

the speed control is engaged. Turns
off when the speed control system
is disengaged.

O/D off:

Illuminates when the

overdrive function of the
transmission has been turned OFF,
refer to the

Driving

chapter. If the

light flashes steadily or does not illuminate, have the transmission
serviced soon, or damage may occur.

Anti-theft system:

Flashes when

the SecuriLock™ Passive Anti-theft
System has been activated.

Throttle Control/Transmission:

Illuminates when a powertrain or an
AWD fault has been detected.
Contact your authorized dealer as
soon as possible.

Turn signal:

Illuminates when the

left or right turn signal or the
hazard lights are turned on. If the
indicators flash faster, check for a burned out bulb.

High beams:

Illuminates when the

high beam headlamps are turned on.

Key-in-ignition warning chime:

Sounds when the key is left in the

ignition in the OFF/LOCK or ACCESSORY position and the driver’s door
is opened.

Headlamps on warning chime:

Sounds when the headlamps or parking

lamps are on, the ignition is off (the key is not in the ignition) and the
driver’s door is opened.

O/D

OFF

2008 Sable

(mgo)

Owners Guide (post-2002-fmt)
USA

(fus)

Instrument Cluster

Содержание Sable 2008









































































































































































































































































































































Результаты поиска

Содержание Sable 2008

Отзывы:

Похожие инструкции для Sable 2008

Бренды по названию

Популярные бренды

Mercury Sable 2008, Руководство пользователя

Результаты поиска

Содержание Sable 2008

Отзывы:

Похожие инструкции для Sable 2008

Бренды по названию

Популярные бренды