Mercury Sable 2008 Скачать руководство пользователя страница 105

Страница: 105 / 328

In AM, FM1, or FM2 mode:

•

Press SEEK to access the
next/previous strong station.

In Satellite radio mode (if
equipped):

•

Press and release SEEK to access
the next/previous strong station.

•

Press and hold SEEK to fast
advance through preset channels
or subscribed channels.

In CD mode:

•

Press SEEK to listen to the next track on the disc.

In any mode:

•

Press VOL up or down to adjust
the volume.

•

Press MUTE to mute the volume.

Navigation system hands free
control feature (if equipped)

Press

briefly until the

voice

icon appears on the

Navigation display to use the voice
command feature.

Press

again to end a voice

command.

For further information on the
Navigation system, refer to the

Navigation supplement.

MUTE

MEDIA

SEEK

VOL

2008 Sable

(mgo)

Owners Guide (post-2002-fmt)
USA

(fus)

Driver Controls

105

Содержание Sable 2008









































































































































































































































































































































Результаты поиска

Содержание Sable 2008

Отзывы:

Похожие инструкции для Sable 2008

Бренды по названию

Популярные бренды

Mercury Sable 2008, Руководство пользователя

Результаты поиска

Содержание Sable 2008

Отзывы:

Похожие инструкции для Sable 2008

Бренды по названию

Популярные бренды