Mercury Sable 2008 Скачать руководство пользователя страница 143

Страница: 143 / 328

Push release button to lower head
restraint.

Using the manual lumbar support (if equipped)

The lumbar support control is
located on the outboard side of the
seatback.

Move the control up or down to
adjust lumbar support.

Folding down the front passenger seatback

The front passenger seatback can be
folded to a horizontal position to
make room for a long load. To fold
the seatback:

1. Move the seat as far back as
possible.

2. Push the head restraint release
button and move the head restraint
fully down.

3. Pull the strap located on the back
of the seat to fold the front passenger seatback.

4. Without releasing the pull strap, push the seatback forward.

5. Move the seat as far forward as possible.

2008 Sable

(mgo)

Owners Guide (post-2002-fmt)
USA

(fus)

Seating and Safety Restraints

143

Содержание Sable 2008









































































































































































































































































































































Результаты поиска

Содержание Sable 2008

Отзывы:

Похожие инструкции для Sable 2008

Бренды по названию

Популярные бренды

Mercury Sable 2008, Руководство пользователя

Результаты поиска

Содержание Sable 2008

Отзывы:

Похожие инструкции для Sable 2008

Бренды по названию

Популярные бренды