Mercury Sable 2008 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 328

background image

Airbag readiness:

If this light fails

to illuminate when the ignition is
turned to ON, continues to flash or
remains on, have the system
serviced immediately by your authorized dealer. A chime will also sound
when a malfunction in the supplemental restraint system has been
detected.

Safety belt:

Reminds you to fasten

your safety belt. A Belt-Minder

威

chime will also sound to remind you
to fasten your safety belt. Refer to
the

Seating and Safety Restraints

chapter to activate/deactivate the Belt-Minder

威

chime feature.

Charging system:

Illuminates when

the battery is not charging properly.

Engine oil pressure:

Illuminates

when the oil pressure falls below the
normal range, refer to

Engine oil

in

the

Maintenance and

Specifications

chapter.

Traction Control™ (if
equipped):

Illuminates when the

Traction Control™ is active or has
been disabled (by the driver or as a
result of a system failure). If the
light remains on, it indicates a
Traction Control Fault. Have the system serviced immediately, refer to
the

Driving

chapter for more information.

Low tire pressure warning:

Illuminates when your tire pressure
is low. If the light remains ON at
start up or while driving, the tire
pressure should be checked. Refer
to

Inflating your tires

in the

Tires, Wheels and Loading

chapter. When

the ignition is first turned to ON, the light will illuminate for 3 seconds to
ensure the bulb is working. If the light does not turn ON or begins to
flash, have the system inspected by your authorized dealer. For more
information on this system, refer to

Tire pressure monitoring system

in

the

Tires, Wheels and Loading

chapter.

2008 Sable

(mgo)

Owners Guide (post-2002-fmt)
USA

(fus)

Instrument Cluster

12

«
...
10
11
12
13
14
...
»

Содержание Sable 2008









































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sable 2008

Green Motion DC 22

Бренд: Eaton Страницы: 65

Бренд: RAM Страницы: 20

Бренд: K&M Страницы: 3

Electronic Parking Disc 3

Бренд: Jacob Jensen Страницы: 2

Бренд: Yakima Страницы: 12

Бренд: Masterack Страницы: 4

Бренд: Over Armour Offroad Страницы: 5

Indigo MANZA QUADRAJET 90

Бренд: TATA Motors Страницы: 10

2011 Civic Sedan

Бренд: Honda Страницы: 5

990E0-54P56-000

Бренд: Suzuki Страницы: 12

Бренд: ACV Страницы: 2

Бренд: Beper Страницы: 52

CERTA CTCVINCVR14A

Бренд: Kogan Страницы: 4

Бренд: Technaxx Страницы: 59

Бренд: Proxel Страницы: 16

Бренд: OEM Audio Страницы: 21

Бренд: BrandMotion Страницы: 9

Бренд: GMC Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды