Mercury Sable 2008 Скачать руководство пользователя страница 174 | Manualshive

Страница: 174 / 328

background image

The airbag SRS is designed to activate when the vehicle sustains lateral
deceleration sufficient to cause the sensors to close an electrical circuit
that initiates airbag inflation.

The fact that the airbags did not inflate in a collision does not mean that
something is wrong with the system. Rather, it means the forces were
not of the type sufficient to cause activation. Side airbags are designed
to inflate in side-impact collisions, not roll-over, rear-impact, frontal or
near-frontal collisions, unless the collision causes sufficient lateral
deceleration.

Several air bag system components get hot after inflation. Do not
touch them after inflation.

If the side airbag has
deployed,

the airbag will

not function again. The side
airbag system (including the
seat) must be inspected and
serviced by an authorized
dealer.

If the airbag is not

replaced, the unrepaired area will
increase the risk of injury in a
collision.

Safety Canopy™ system

Do not place objects or
mount equipment on or

near the headliner at the siderail
that may come into contact with a
deploying Safety Canopy™.
Failure to follow these instructions
may increase the risk of personal
injury in the event of a collision.

2008 Sable

(mgo)

Owners Guide (post-2002-fmt)
USA

(fus)

Seating and Safety Restraints

174

«
...
172
173
174
175
176
...
»

Содержание Sable 2008









































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sable 2008

Бренд: FormFit Страницы: 4

Бренд: Edelbrock Страницы: 2

Бренд: Gator Страницы: 8

10-8002-C11670C

Бренд: Saleen Страницы: 17

STEALTH POWER RBP-216-SP

Бренд: RBP Страницы: 16

STREET SUPER SHIFTER

Бренд: HURST Страницы: 2

Бренд: Opel Страницы: 254

Бренд: SuperATV Страницы: 7

Бренд: Mercedes-Benz Страницы: 358

Бренд: Pyle Страницы: 2

Бренд: Quadratec Страницы: 6

Бренд: THIEYE Страницы: 88

Bluetooth Phone System 2010

Бренд: Kia Страницы: 16

Бренд: TOPPOINT Страницы: 2

Dynamic Power Management Home - Module

Бренд: newmotion Страницы: 20

Бренд: WABCO Страницы: 224

Бренд: Volvo Страницы: 362

Dodge Caravan 2002

Бренд: Chrysler Страницы: 2399

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды