Mercury Sable 2008 Скачать руководство пользователя страница 232 | Manualshive

Страница: 232 / 328

background image

If the steering wanders or pulls, check for:

•

an improperly inflated tire

•

uneven tire wear

•

loose or worn suspension components

•

loose or worn steering components

•

improper steering alignment

AUTOMATIC TRANSAXLE OPERATION

Brake-shift interlock

This vehicle is equipped with a brake-shift interlock feature that prevents
the gearshift lever from being moved from P (Park) when the ignition is
in the RUN position unless brake pedal is depressed.

If you cannot move the gearshift lever out of P (Park) with ignition in
the RUN position and the brake pedal depressed:

1. Apply the parking brake, turn
ignition key to LOCK, then remove
the key.

2. Using a screwdriver (or similar
tool), remove the protective cover
to the interlock release access hole
on the console.

3. Insert the screwdriver (or similar
tool) into the access hole and press
downward while pulling the
gearshift lever out of the P (Park)
position and into the N (Neutral)
position.

4. Remove the tool and reinstall the
protective cover.

5. Start the vehicle and release the
parking brake.

If it is necessary to use the above procedure to move the gearshift lever,
it is possible that a fuse has blown or the vehicle’s brakelamps are not
operating properly. Refer to

Fuses and relays

in the

Roadside

Emergencies

chapter.

2008 Sable

(mgo)

Owners Guide (post-2002-fmt)
USA

(fus)

Driving

232

«
...
230
231
232
233
234
...
»

Содержание Sable 2008









































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sable 2008

Бренд: Jeep Страницы: 25

Бренд: Yakima Страницы: 11

Бренд: UltraGauge Страницы: 55

Бренд: Fiat Страницы: 24

Бренд: Valeo Страницы: 28

Бренд: Skoda Страницы: 165

Бренд: Velleman Страницы: 12

Бренд: Improved Racing Страницы: 17

Бренд: S&B Filters Страницы: 4

Бренд: Mazda Страницы: 3

Бренд: Meritor Страницы: 20

SB-J-GCHER2/10W3v2

Бренд: Stealthbox Страницы: 2

Бренд: Whispbar Страницы: 77

Gigaware 12-493

Бренд: Gigaware Страницы: 8

Бренд: Buick Страницы: 394

Бренд: Edelbrock Страницы: 2

Бренд: Curt Manufacturing Страницы: 5

Бренд: Kia Страницы: 417

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды