Mercury 3.0L Carbureted Alpha Скачать руководство пользователя | Manualshive

Страница: 39 / 137

background image

GASOLINE STERNDRIVE INSTALLATION MANUAL

90-860172011

Page 39 of 137

Driveshaft Extension Models

If your power package is equipped with a driveshaft extension, refer to the Driveshaft
Extension Installation Instructions included with your engine package.

Engine Preparation

1. Remove and read all tags attached to engine.

2. Remove the plug from the engine coupler.

3. Remove all hardware that secures engine to shipping container.

4. Connect battery cables to engine. Be sure to observe the following:

a. Make sure that grounding stud and starter solenoid terminal are free of paint or any

other material that could cause a poor electrical connection.

b. After battery cables are connected, apply a thin coat of sealant to the terminals.

Description

Where Used

Part Number

A

Liquid Neoprene

Battery Terminals

92-25711-2

c. Be sure to slide rubber boot over positive (+) terminal after making connection.

5. Drape battery cables over top of engine to prevent interference during installation.

IMPORTANT: There is a fuse located at the starter solenoid. DO NOT remove this fuse.
The positive battery cable must be connected to the same stud as the fuse.

74907

b

c

d

a

a -

Positive (+) Battery Cable

b -

Starter Solenoid

c -

90 Amp Fuse - DO NOT Remove

d -

Rubber Boot Location

6. Remove shipping plug from coupler and lubricate splines.

Description

Where Used

Part Number

A

Engine Coupler Spline Grease

Coupler Splines

92-816391A4

7. Install quick oil drain hose plug in oil drain hose.

8. Install the fuel inlet fitting.

«
...
37
38
39
40
41
...
»

Содержание 3.0L Carbureted Alpha










































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3.0L Carbureted Alpha

Бренд: SAESHIN Страницы: 2

Бренд: phytron Страницы: 29

Бренд: Parker Страницы: 32

Бренд: Daewoo Страницы: 199

Бренд: Onan Страницы: 341

Бренд: Lenze Страницы: 76

Бренд: Fabtex Страницы: 4

Бренд: MTU Страницы: 187

2005 ENDUCROSS EC 125

Бренд: GAS GAS Страницы: 50

124 Twin Cam Style

Бренд: S&S Cycle Страницы: 20

Бренд: Volvo Penta Страницы: 61

Бренд: Volvo Penta Страницы: 92

Бренд: Volvo Penta Страницы: 216

Бренд: Lycoming Страницы: 90

IntelliGear Plus

Бренд: Browning Страницы: 20

Бренд: YS Страницы: 2

Бренд: Electro motive Страницы: 287

Бренд: O.S. engine Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды