Mercury 3.0L Carbureted Alpha Скачать руководство пользователя

Страница: 24 / 137

GASOLINE STERNDRIVE INSTALLATION MANUAL

Page 24 of 137

90-860172011

NOTE: The quick release button on hose fitting must be positioned away from water inlet
fitting, or block-off plate if equipped. Release button must not contact water fitting or
block-off plate, if equipped.

NOTE: The hose must not come into contact with the steering system components or the
engine coupler and drive shaft.

3. Select a mounting location for coolant recovery bottle and mounting bracket that meets

all of the following:

•

Within limits of clear plastic tubing.

•

Level with or above the heat exchanger fill neck.

•

Accessible for observing coolant level and filling.

4. Mount coolant recovery bottle and mounting bracket in desired location using two

3/4 in. (19 mm) long screws and flat washers.

5. Route plastic tubing to recovery bottle. Ensure that tubing is positioned away from any

moving parts. Cut plastic tubing as required and connect to bottom connection on
recovery bottle and secure with tubing clamp provided.

6. Fasten plastic tubing to boat, as necessary, with 2 hose clips and 1/2 in. (13 mm) long

screws (provided).

71712

a -

Recovery Bottle And Mounting Bracket

b -

Screws And Flat Washers

c -

Plastic Tubing

d -

Tubing Clamp

Содержание 3.0L Carbureted Alpha










































































































































Результаты поиска

Содержание 3.0L Carbureted Alpha

Отзывы:

Похожие инструкции для 3.0L Carbureted Alpha

Бренды по названию

Популярные бренды

Mercury 3.0L Carbureted Alpha, Руководство по установке

Результаты поиска

Содержание 3.0L Carbureted Alpha

Отзывы:

Похожие инструкции для 3.0L Carbureted Alpha

Бренды по названию

Популярные бренды