Mercury 3.0L Carbureted Alpha Скачать руководство пользователя

Страница: 113 / 137

GASOLINE STERNDRIVE INSTALLATION MANUAL

90-860172011

Page 113 of 137

CHECKING SHIFT OPERATION

With sterndrive unit installed and engine running, ensure that drive unit shifts properly, as
explained following:

1. Shift into FORWARD and REVERSE gear, making sure that clutch engages before

engine begins to accelerate.

2. Accelerate engine while in FORWARD and REVERSE gear to ensure that engine does

not stop.

3. Check that shift cutout switch plunger pin is centered in notch of shift cutout lever with

drive unit in FORWARD and REVERSE gear.

75435

a -

Cutout Switch Plunger Pin

4. If the proper results are not achieved in the previous steps, shift cables must be

readjusted.

5. Shifting from FORWARD and REVERSE to NEUTRAL: ensure drive unit is in NEUTRAL

before remote control shift lever comes to the NEUTRAL detent position. Perform this
check using various shifting rates to ensure that the drive unit shifts the same whether
shifting fast or slow.

Содержание 3.0L Carbureted Alpha










































































































































Результаты поиска

Содержание 3.0L Carbureted Alpha

Отзывы:

Похожие инструкции для 3.0L Carbureted Alpha

Бренды по названию

Популярные бренды

Mercury 3.0L Carbureted Alpha, Руководство по установке

Результаты поиска

Содержание 3.0L Carbureted Alpha

Отзывы:

Похожие инструкции для 3.0L Carbureted Alpha

Бренды по названию

Популярные бренды