Mercury 3.0L Carbureted Alpha Скачать руководство пользователя

Страница: 96 / 137

GASOLINE STERNDRIVE INSTALLATION MANUAL

Page 96 of 137

90-860172011

3. Before installing the shift cable into the control box, extend the stainless rod eye end of

the cable and grease it with 2-4-C Marine Lubricant with Teflon. Move it back and forth
to allow even distribution of the grease.

22005

Description

Where Used

Part Number

2-4-C Marine Lubricant With
Teflon

Shift Cable End

92-825407A3

4. Do not strap or clamp the control cables to any other cables or rigid structure within

3 ft. (914 mm) of the control box.

5. Be sure the cable is not permanently kinked.

6. Make sure there is proper clearance for cable movement when the control box is

installed in the side panel. The cables must have room to move up and down when the
control handle is shifted into either FORWARD or REVERSE.

7. Ensure that the engine was not set down on the intermediate shift cable during

installation, as this will crush the inner cable tubing and cause improper and / or stiff
shifting.

8. DO NOT fasten the shift cable with straps or clamps to any other cable within 5 ft.

(1.5 m) of the shift plate.

9. DO NOT fasten the shift cable to the transom with any type of plastic clips or fasteners

within 5 ft. (1.5 m) of the shift plate.

10. DO NOT overtighten the throttle or shift cable attaching nuts at the engine end. Barrel

and cable end must be free to rotate on the mounting stud.

NOTE: Lubricate attaching points with engine oil.

Description

Where Used

Part Number

SAE 30W Engine Oil

Shift Cable Pivot Points

Obtain Locally

Содержание 3.0L Carbureted Alpha










































































































































Результаты поиска

Содержание 3.0L Carbureted Alpha

Отзывы:

Похожие инструкции для 3.0L Carbureted Alpha

Бренды по названию

Популярные бренды

Mercury 3.0L Carbureted Alpha, Руководство по установке

Результаты поиска

Содержание 3.0L Carbureted Alpha

Отзывы:

Похожие инструкции для 3.0L Carbureted Alpha

Бренды по названию

Популярные бренды