Mercury 3.0L Carbureted Alpha Скачать руководство пользователя | Manualshive

Страница: 6 / 137

background image

GASOLINE STERNDRIVE INSTALLATION MANUAL

Page 6 of 137

90-860172011

Special Tools

Description

Part Number

Transom Drilling Fixture

91-43693A2

Engine Alignment Tool

91-805475A1

Shift Cable Adjustment Tool

91-12427

Engine Mount Drilling Fixture

91-806794A1

Tapered Insert Tool

91-43579

Shift Shaft Slide Stabilizer Tool

91-809815A1

Alpha Notice: Increased Trim-In Range Capability

The Alpha trim cylinders provide the capability for an increased trim-in range. A spacer can
be removed from the trim cylinders to increase the trim-in range by approximately 1-1/2
degrees. This will improve the acceleration on some boats by forcing the bow down more
quickly. If the spacers are to be removed, the boat must be water tested to ensure that the
increased trim-in range does not cause any undesired boat handling characteristics
(bow-steer, chine-walk, etc.) if the sterndrive is trimmed in while the boat is operated at
higher speeds. The boat should be tested under all conceivable load conditions and
maneuvers to ensure that the additional trim-in does not pose a problem. The final decision
and responsibility for use of the additional trim-in range is left up to the boat manufacturer.

WARNING

It is recommended that only qualified personnel adjust the Trim-In Limit Spacer.
Boat must be water tested after adjusting or removing the device to ensure that the
modified trim-in range does not cause the boat to exhibit an undesirable boat handl-
ing characteristic if the sterndrive unit is trimmed in at higher speeds. Increased
trim-in range may cause handling problems on some boats that could result in per-
sonal injury.

«
...
4
5
6
7
8
...
»

Содержание 3.0L Carbureted Alpha










































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3.0L Carbureted Alpha

Бренд: Garmin Страницы: 14

Бренд: Navistar Страницы: 197

Бренд: Leb Electronics Страницы: 24

Бренд: Mercedes-Benz Страницы: 324

Бренд: Vetus Страницы: 28

Бренд: Yamaha Страницы: 51

Бренд: Volvo Penta Страницы: 53

Бренд: Volvo Penta Страницы: 76

Бренд: Clarke Страницы: 49

Бренд: WÜRGES Страницы: 24

Бренд: Hacker Страницы: 2

Бренд: Hacker Страницы: 7

Бренд: Hacker Страницы: 8

Бренд: Hacker Страницы: 8

Бренд: Hacker Страницы: 8

Бренд: Hacker Страницы: 8

Бренд: Hacker Страницы: 38

Бренд: Yanmar Страницы: 70

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды