Mercury 3.0L Carbureted Alpha Скачать руководство пользователя

Страница: 110 / 137

GASOLINE STERNDRIVE INSTALLATION MANUAL

Page 110 of 137

90-860172011

7. Start engine and run at idle rpm until water temperature is normal.

8. Watch all gauges for normal readings.

9. Turn steering wheel RIGHT/STARBOARD, then LEFT/PORT, and ensure drive unit

turns the correct way.

10. Inspect engine compartment for water, oil, fuel and exhaust leaks.

11. Turn steering wheel PORT until it stops and continue to apply pressure. If pump lugs

(engine rpm drops and/or power steering pump tone changes):

a. Check for an obstruction between gimbal ring and gimbal housing and all moving

steering components.

b. Check that steering lever is not contacting cutout in transom. If contact is being

made, modify cutout.

12. Turn steering wheel STARBOARD until it stops and continue to apply pressure. If pump

lugs (engine rpm drops and/or power steering pump tone changes):

a. Check same items as a. and b. above.

b. Check steering cable end dimension with cable FULLY EXTENDED.

13. Check power steering fluid level.

a. Turn off engine.

b. Remove cap/dipstick from power steering pump. Check fluid level and add if

necessary.

22023

a -

Dipstick (Full When Hot Line)

Содержание 3.0L Carbureted Alpha










































































































































Результаты поиска

Содержание 3.0L Carbureted Alpha

Отзывы:

Похожие инструкции для 3.0L Carbureted Alpha

Бренды по названию

Популярные бренды

Mercury 3.0L Carbureted Alpha, Руководство по установке

Результаты поиска

Содержание 3.0L Carbureted Alpha

Отзывы:

Похожие инструкции для 3.0L Carbureted Alpha

Бренды по названию

Популярные бренды