Mercury 3.0L Carbureted Alpha Скачать руководство пользователя

Страница: 127 / 137

GASOLINE STERNDRIVE INSTALLATION MANUAL

90-860172011

Page 127 of 137

Refer to gauge manufacturer’s instructions for specific connections.

NOTE:

Connect Wires Together with Screw and Hex Nut; Apply Liquid Neoprene to

Connection and Slide Rubber Sleeve over Connection.

NOTE:

Power for a Fused Accessory Panel May Be Taken from This Connection. Load

Must Not Exceed 40 Amps. Panel Ground Wire Must Be Connected to Instrument Terminal
That Has an 8-Gauge Black (Ground) Harness Wire Connected to it.

NOTE:

Lanyard stop switch lead and neutral safety switch leads must be soldered and

covered with shrink tube for a water proof connection. If an alternate method of connection
is made, verify connection is secure and sealed for a water proof connection.

a -

Audio Warning Alarm

b -

Tachometer

c -

Oil Pressure

d -

Water Temperature

e -

Battery Meter

f -

Ignition Switch

g -

Trim Indicator

h -

Read/Observe NOTE 1 and 2.

i -

Read/Observe NOTE 3.

j -

To Engine Wiring Harness

Содержание 3.0L Carbureted Alpha










































































































































Результаты поиска

Содержание 3.0L Carbureted Alpha

Отзывы:

Похожие инструкции для 3.0L Carbureted Alpha

Бренды по названию

Популярные бренды

Mercury 3.0L Carbureted Alpha, Руководство по установке

Результаты поиска

Содержание 3.0L Carbureted Alpha

Отзывы:

Похожие инструкции для 3.0L Carbureted Alpha

Бренды по названию

Популярные бренды