Mercury 3.0L Carbureted Alpha Скачать руководство пользователя | Manualshive

Страница: 107 / 137

background image

GASOLINE STERNDRIVE INSTALLATION MANUAL

90-860172011

Page 107 of 137

BATTERY CONNECTION

IMPORTANT: Engine electrical system is negative (–) ground.

1. Connect engine positive (+) battery cable (usually RED) to positive (+) battery terminal.

2. Connect engine negative (–) battery cable (usually BLACK) to negative (–) battery

terminal.

3. Connect Power Trim pump BLACK (–) battery cable to negative (–) battery terminal and

trim pump RED (+) battery cable to positive (+) battery terminal.

4. Make sure that all battery terminal connections are tight. Then spray terminals with a

battery connection sealant to help retard corrosion.

Test Running Engine

WARNING

Avoid Injury: If engine is to be tested with the boat out of the water, the propeller
must be removed to avoid injury.

CAUTION

Overheating from insufficient cooling water will cause engine and drive damage.
Ensure that there is sufficient water always available at the water inlet holes during
operation.

BOAT OUT OF THE WATER

For engine operation tests with the boat out of the water:

IMPORTANT: If using a flushing attachment over the water inlet holes and a water
hose as shown, do not use full water source pressure.

1. Install a flushing attachment over the sterndrive water inlet holes.

2. Connect a hose between the flushing attachment and a water source.

3. Open the water source about 1/2 maximum. DO NOT use full water pressure.

70564

a

b

a -

Flushing Attachment

b -

Water Hose

IMPORTANT: Engines with the sterndrive water inlet blocked off at the gimbal
housing and using a through the hull water inlet, need a supply of cooling water
available to both the sterndrive unit and to the engine during operation.

«
...
105
106
107
108
109
...
»

Содержание 3.0L Carbureted Alpha










































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3.0L Carbureted Alpha

Бренд: BAFANG Страницы: 5

Бренд: BAFANG Страницы: 12

Бренд: WPT POWER Страницы: 39

General Pump 103166

Бренд: Interpump Group Страницы: 3

Бренд: GR Страницы: 8

Бренд: O.S. engine Страницы: 18

Бренд: O.S. engine Страницы: 24

BREVINI D 072 Series

Бренд: DANA Страницы: 58

BREVINI M Series

Бренд: DANA Страницы: 40

OMA-3815-1000-W

Бренд: O.S. engine Страницы: 2

Бренд: O.S. engine Страницы: 22

Бренд: O.S. engine Страницы: 23

Бренд: O.S. engine Страницы: 43

Бренд: Alutech Страницы: 32

Бренд: Honda Страницы: 42

Бренд: Cors-Air Страницы: 10

Бренд: GEA Страницы: 78

Бренд: Beamz Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды