Mercury 3.0L Carbureted Alpha Скачать руководство пользователя

Страница: 49 / 137

GASOLINE STERNDRIVE INSTALLATION MANUAL

90-860172011

Page 49 of 137

Engine Alignment

1. Ensure that the dust cover is removed or folded back out of the way.

22027

a -

Dust Cover

CAUTION

DO NOT use an alignment tool from another manufacturer. Alignment tools other
than Quicksilver Alignment Tool may cause improper alignment and damage to
gimbal bearing and/or engine coupler.

2. Attempt to insert the solid end of the alignment tool through the gimbal bearing and into

the engine coupler splines.

3. If the tool does not fit, remove it and carefully raise or lower the front end of the engine

using the center alignment eye and attempt to insert the alignment tool.

Содержание 3.0L Carbureted Alpha










































































































































Результаты поиска

Содержание 3.0L Carbureted Alpha

Отзывы:

Похожие инструкции для 3.0L Carbureted Alpha

Бренды по названию

Популярные бренды

Mercury 3.0L Carbureted Alpha, Руководство по установке

Результаты поиска

Содержание 3.0L Carbureted Alpha

Отзывы:

Похожие инструкции для 3.0L Carbureted Alpha

Бренды по названию

Популярные бренды