Mercury 3.0L Carbureted Alpha Скачать руководство пользователя | Manualshive

Страница: 72 / 137

background image

GASOLINE STERNDRIVE INSTALLATION MANUAL

Page 72 of 137

90-860172011

Bravo Models

NOTE: Using Adjustment Tool (91-12427), shift cables can be adjusted without or with the
sterndrive installed, using the following procedure.

IMPORTANT: Sterndrive unit propeller rotation is determined by the shift cable
installation in the remote control.

•

Bravo One/Two - If shift cable end guide moves in direction

A

when control lever

is placed in FORWARD, remote control is set up for RIGHT HAND (RH) propeller
rotation.

•

Bravo One/Two - If shift cable end guide moves in direction

B

when control lever

is placed in FORWARD, remote control is set up for LEFT HAND (LH) propeller
rotation.

71656

A

B

Arrow Indicates Direction Of Motion

•

Bravo Three - Front propeller on sterndrive unit is always LH Rotation and rear
propeller is always RH Rotation. Shift cable end guide must move in direction

A

,

when control lever is placed in FORWARD gear position.

71656

A

IMPORTANT: When installing shift cables, be sure that cables are routed in such a
way as to avoid sharp bends and/or contact with moving parts. DO NOT fasten any
items to shift cables.

1. Install shift cable into remote control. (Refer to appropriate remote control instructions.)

2. Remove the guide.

3. Loosen stud and move it to dimension, as shown. Retighten stud.

71657

a

b

a -

Stud

b -

3 in. (76 mm) (Center Of Pivot Bolt To Center Of Stud)

«
...
70
71
72
73
74
...
»

Содержание 3.0L Carbureted Alpha










































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3.0L Carbureted Alpha

Бренд: YOODA Страницы: 7

MICROPUMP EagleDrive MS

Бренд: Idex Страницы: 23

Бренд: TAYO Страницы: 42

Бренд: Motor Power Company Страницы: 59

Бренд: Briggs & Stratton Страницы: 4

Бренд: Daedong Страницы: 66

Throttling Governor Kerosene Stationary Engines

Бренд: Worthington Страницы: 33

Бренд: Clinton Страницы: 23

Бренд: Chamberlain Страницы: 20

Бренд: RADEMACHER Страницы: 72

Бренд: LRP Страницы: 4

Бренд: Fagor Страницы: 174

Бренд: Homa Страницы: 34

Бренд: Yanmar Страницы: 182

BLACK DEVIL PRO

Бренд: Cors-Air Страницы: 17

Бренд: Briggs & Stratton Страницы: 16

Бренд: Honda Страницы: 65

Бренд: EMAK Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды