MerCruiser 350 MAG MPI Скачать руководство пользователя страница 55

Страница: 55 / 150

Section 3 - On The Water

90-864195070 JUNE 2007

Page 47

Drain Plug and Bilge Pump

The engine compartment in your boat is a natural place for water to collect. For this reason,

boats are normally equipped with a drain plug and/or a bilge pump. It is very important to

check these items on a regular basis to ensure that the water level does not come into

contact with your power package. Components on your engine will be damaged if

submerged. Damage caused by submersion is not covered by the Mercury MerCruiser

Limited Warranty.

Basic Boat Operation (DTS Models)

Launching and Boat Operation

IMPORTANT: Install bilge drain plug prior to launching boat.

OPERATION CHART

Operation Chart

BEFORE STARTING

AFTER STARTING

WHILE UNDERWAY

AFTER STOPPING

Install bilge drain plug.

Observe all gauges to

check condition of

engine. If not normal, stop

engine.

Observe all gauges to

check condition of engine. If

not normal, stop engine.

Turn ignition key to the

"OFF" position.

Open engine hatch.

Check for fuel, oil, water,

fluid and exhaust leaks.

Listen for the audio alarm. Turn battery switch to the

"OFF" position.

Turn battery switch on.

Check shift and throttle

control operation.

Close fuel shut off valve.

Operate bilge blowers.

Check steering operation.

Close seacock, if

equipped.

Open fuel shut off valve.

Flush cooling system if in

saltwater.

Open seacock, if

equipped.

Drain bilge.

Close the drain system.
Place sterndrive unit in

full down/in position.
Check the engine oil.
Perform all other checks

specified by your dealer

and/or boat builder.
Listen for Audio Warning

Alarm to sound when the

ignition switch is in the

"ON" position.

Starting and Stopping the Engine

NOTE: Perform only those functions applicable to your power package.

STARTING THE ENGINE

1. Check all items listed in the Operation Chart.
2. Place the remote control handle in neutral.

Содержание 350 MAG MPI























































































































































Результаты поиска

Содержание 350 MAG MPI

Отзывы:

Похожие инструкции для 350 MAG MPI

Бренды по названию

Популярные бренды

MerCruiser 350 MAG MPI, Руководство пользователя

Результаты поиска

Содержание 350 MAG MPI

Отзывы:

Похожие инструкции для 350 MAG MPI

Бренды по названию

Популярные бренды