MerCruiser 350 MAG MPI Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 150

background image

Section 2 - Getting to Know Your Power Package

Page 38

90-864195070 JUNE 2007

7. The Quicksilver MerCathode System has a 20 amp in‑line fuse in the wire which

connects to the positive (+) terminal on controller. If the fuse is blown, the system will

not operate resulting in a loss of corrosion protection.

mc79977

Audio Warning System

Your Mercury MerCruiser power package may be equipped with an Audio Warning System.

The Audio Warning System will not protect the engine from damage. It is designed to warn

the operator that a problem has occurred.
The audio warning system will sound with a continuous horn if one of the following occurs:
• Engine oil pressure too low
• Engine temperature too hot
• Seawater pressure too low
The audio warning system will sound with an intermittent beeping if the following occurs:
• Sterndrive oil level too low

NOTICE

A continuous horn indicates a critical fault. Operating the engine during a critical fault can

damage components. If the warning horn emits a continuous beep, do not operate the

engine unless avoiding a hazardous situation.

If the alarm sounds, stop the engine immediately. Investigate cause and correct it, if

possible. If the cause cannot be determined, contact your authorized Mercury MerCruiser

dealer.

Testing The Audio Warning System

1. Turn the ignition switch to the "ON" position without cranking the engine.
2. Listen for the audio alarm. The alarm will sound if the system is functioning correctly.

Engine Guardian Strategy

IMPORTANT: Boat speed could be reduced to idle and may not respond to the throttle.
Engine Guardian Strategy is designed to help reduce the potential for engine damage by

reducing engine power when a potential problem is sensed by the ECM. Engine Guardian

monitors:
• Oil pressure
• Coolant temperature
• Seawater pressure
• Engine overspeed
• Exhaust Manifold Temperature [8.1 liter (496 cid) engines only]

«
...
44
45
46
47
48
...
»

Содержание 350 MAG MPI























































































































































Отзывы:

Нет отзывов

Похожие инструкции для 350 MAG MPI

Бренд: Farymann Diesel Страницы: 80

ALCYO ACCU-TRK-AT

Бренд: Oben Страницы: 28

Бренд: DLA Страницы: 7

Бренд: Yanmar Страницы: 52

Бренд: IMS Страницы: 6

Бренд: Komatsu Utility Страницы: 32

Бренд: Siemens Страницы: 28

6FB1203-5AT00-7MP0

Бренд: Siemens Страницы: 7

COMBIMASTER CM110/3

Бренд: Siemens Страницы: 21

Бренд: Siemens Страницы: 19

Бренд: Siemens Страницы: 24

Бренд: Siemens Страницы: 15

Бренд: Siemens Страницы: 16

Бренд: Siemens Страницы: 38

Бренд: Siemens Страницы: 24

Бренд: Siemens Страницы: 36

Бренд: Siemens Страницы: 40

Бренд: Siemens Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды