MerCruiser 350 MAG MPI Скачать руководство пользователя страница 138

Страница: 138 / 150

Section 6 - Storage

Page 130

90-864195070 JUNE 2007

3. On models with a seawater pickup pump, remove the two blue drain plugs. If the

seawater pickup pump does not have blue drain plugs, or you are unable to access

them, loosen the clamps and remove both hoses.

6145

a -

Hose clamps

b -

Blue drain plugs

4. Crank the engine over slightly with starter motor to purge any water trapped in the

seawater pickup pump. Do not allow the engine to start.

5. After the cooling system has been drained completely, install the drain plugs, reconnect

hoses, and tighten all hose clamps securely.

Draining the Sterndrive

NOTE: This procedure is needed only for salty, brackish, mineral laden, or polluted water

applications; and for freezing temperatures or extended storage.

1. Insert a small wire repeatedly to make sure that vent holes, water drain holes, and

passages are unobstructed and open.

6146

Sterndrive Water Drain Holes

a -

Speedometer pitot tube

b -

Trim tab cavity vent hole

c -

Trim tab cavity drain passage

d -

Gear housing water drain hole (1

each ‑ port and starboard)

e -

Gear housing cavity vent hole

f -

Gear housing cavity drain hole

NOTICE

The universal joint bellows may develop a set when stored in a raised or up position,

causing the bellows to fail when returned to service and allowing water to enter the boat.

Store the sterndrive in the full down position.

2. Lower the sterndrive unit to the full down/in position.

Содержание 350 MAG MPI























































































































































Результаты поиска

Содержание 350 MAG MPI

Отзывы:

Похожие инструкции для 350 MAG MPI

Бренды по названию

Популярные бренды

MerCruiser 350 MAG MPI, Руководство пользователя

Результаты поиска

Содержание 350 MAG MPI

Отзывы:

Похожие инструкции для 350 MAG MPI

Бренды по названию

Популярные бренды