MerCruiser 350 MAG MPI Скачать руководство пользователя страница 135

Страница: 135 / 150

Section 6 - Storage

90-864195070 JUNE 2007

Page 127

2. Remove the blue drain plug from the distribution housing (lower front, port side).

6138

a -

Blue drain plug

3. To properly vent the cooling system, remove the blue drain plug from the side of the

thermostat housing within 30 seconds.

6139

a -

Blue drain plug location

4. Remove the two blue drain plugs from the seawater pickup pump (front, starboard side).

6140

a -

Blue drain plugs

5. Verify that water is draining from each opening.
6. Allow the system to drain for a minimum of five minutes. Mercury MerCruiser

recommends leaving the drain system open while transporting the boat or while

performing other maintenance to ensure that all water is drained.

7. Crank the engine over slightly with starter motor to purge any water trapped in the

seawater pickup pump. Do not allow the engine to start.

8. Prior to launching the boat or starting the engine, close the drain system by installing

the four blue drain plugs.

9. Open the seacock, if equipped, or unplug and reconnect the water inlet hose prior to

operating the engine.

Содержание 350 MAG MPI























































































































































Результаты поиска

Содержание 350 MAG MPI

Отзывы:

Похожие инструкции для 350 MAG MPI

Бренды по названию

Популярные бренды

MerCruiser 350 MAG MPI, Руководство пользователя

Результаты поиска

Содержание 350 MAG MPI

Отзывы:

Похожие инструкции для 350 MAG MPI

Бренды по названию

Популярные бренды