MerCruiser 350 MAG MPI Скачать руководство пользователя страница 91

Страница: 91 / 150

Section 5 - Maintenance

90-864195070 JUNE 2007

Page 83

GEN II Models

6527

a -

Fuel filter mounting bracket

b -

Sealing ring

c -

Fuel filter

REMOVAL

1. Allow the engine to cool down.

NOTE: Mercury MerCruiser recommends that the engine be shut off for 12 hours prior to

filter removal.

2. Close fuel supply valve, if equipped.
3. Wrap the water‑separating fuel filter with a cloth to help catch any fuel spills or spray.
4. Remove and discard the water‑separating fuel filter and sealing ring from the mounting

bracket.

INSTALLATION

1. Coat the sealing ring on the new filter with engine oil.

Tube Ref No.

Description

Where Used

Part No.

SAE Engine Oil 30W

Water-separating fuel filter

sealing ring

Obtain Locally

2. Thread filter onto the mounting bracket and tighten securely by hand. Do not use a filter

wrench.

3. Open fuel supply valve, if equipped.
4. Ensure that engine compartment is properly ventilated.

NOTICE

Failure to provide sufficient cooling water will damage the water pump and cause the

engine to overheat. Provide a sufficient supply of water at the water inlets during

operation.

5. Supply cooling water to the engine.
6. Start the engine. Check for gasoline leaks around the fuel filter assembly. If leaks exist,

stop the engine immediately. Recheck the filter installation, wipe up any spilled fuel,

and properly ventilate the engine compartment. If leaks continue, stop engine

immediately and contact your authorized Mercury MerCruiser dealer.

Содержание 350 MAG MPI























































































































































Результаты поиска

Содержание 350 MAG MPI

Отзывы:

Похожие инструкции для 350 MAG MPI

Бренды по названию

Популярные бренды

MerCruiser 350 MAG MPI, Руководство пользователя

Результаты поиска

Содержание 350 MAG MPI

Отзывы:

Похожие инструкции для 350 MAG MPI

Бренды по названию

Популярные бренды