MerCruiser 350 MAG MPI Скачать руководство пользователя страница 80

Страница: 80 / 150

Section 5 - Maintenance

Page 72

90-864195070 JUNE 2007

CHANGING FILTER

1. Remove and discard oil filter.

6068

a -

Oil filter

2. Coat sealing ring on new filter with engine oil and install.
3. Tighten oil filter securely (following filter manufacturer's instructions). Do not

overtighten.

4. Remove oil fill cap.
IMPORTANT: Always use dipstick to determine exactly how much oil is required.
5. Add recommended engine oil to bring level up to the bottom of the OK range on the

dipstick.

6. With the boat at rest in the water, check the oil level and add specified fluid to bring the

oil level up to, but not over, the full or OK range.

NOTE: Adding 0.95 liters (1 quart) of engine oil will raise the level from the add mark to the

top of the OK range.

Engine Model

Engine Oil Capacity

Fluid type

4.3L MPI

3.8 liters (4 U.S. qt.)

Mercury/Quicksilver Synthetic Blend

MerCruiser Engine Oil 25W‑40

5.0 MPI, 350 MAG MPI, MX 6.2 MPI

5.7L (350 cid)

4.25 liters (4.5 U.S. qt.)

7. Start the engine, run the engine for three minutes, and check for leaks. Stop the engine.

Allow approximately 5 minutes for the oil to drain into the oil pan. The boat must be at

rest in the water.

Power Steering Fluid

Checking

1. Stop the engine and center the sterndrive unit.
2. Remove the fill cap/dipstick and observe the level.

Proper fluid level with engine at normal operating temperature should be within

the warm range.

Содержание 350 MAG MPI























































































































































Результаты поиска

Содержание 350 MAG MPI

Отзывы:

Похожие инструкции для 350 MAG MPI

Бренды по названию

Популярные бренды

MerCruiser 350 MAG MPI, Руководство пользователя

Результаты поиска

Содержание 350 MAG MPI

Отзывы:

Похожие инструкции для 350 MAG MPI

Бренды по названию

Популярные бренды