MerCruiser 350 MAG MPI Скачать руководство пользователя страница 59

Страница: 59 / 150

Section 3 - On The Water

90-864195070 JUNE 2007

Page 51

Passenger Safety In Pontoon Boats And Deck Boats

Whenever the boat is in motion, observe the location of all passengers. Do not allow any

passengers to stand or use seats other than those designated for traveling faster than idle

speed. A sudden reduction in boat speed, such as plunging into a large wave or wake, a

sudden throttle reduction, or a sharp change of boat direction, could throw them over the

front of boat. Falling over the front of the boat between the two pontoons will position them

to be run over.

Boats Having An Open Front Deck

No one should ever be on the deck in front of the fence while the boat is in motion. Keep

all passengers behind the front fence or enclosure.
Persons on the front deck could easily be thrown overboard or persons dangling their feet

over the front edge could get their legs caught by a wave and pulled into the water.

mc79555-1

WARNING

Sitting or standing in an area of the boat not designed for passengers at speeds above

idle can cause serious injury or death. Stay back from the front end of deck boats or

raised platforms and remain seated while the boat is in motion.

Boats With Front‑Mounted, Raised Pedestal Fishing Seats

Elevated fishing seats are not intended for use when the boat is traveling faster than idle

or trolling speed. Sit only in seats designated for traveling at faster speeds.
Any unexpected, sudden reduction in boat speed could result in the elevated passenger

falling over the front of the boat.

mc79557-1

Wave And Wake Jumping

WARNING

Wave or wake jumping can cause serious injury or death from occupants being thrown

within or out of the boat. Avoid wave or wake jumping whenever possible.

mc79680-1

Содержание 350 MAG MPI























































































































































Результаты поиска

Содержание 350 MAG MPI

Отзывы:

Похожие инструкции для 350 MAG MPI

Бренды по названию

Популярные бренды

MerCruiser 350 MAG MPI, Руководство пользователя

Результаты поиска

Содержание 350 MAG MPI

Отзывы:

Похожие инструкции для 350 MAG MPI

Бренды по названию

Популярные бренды