MerCruiser 350 MAG MPI Скачать руководство пользователя страница 90

Страница: 90 / 150

Section 5 - Maintenance

Page 82

90-864195070 JUNE 2007

Positive Crankcase Ventilation Valve (PCV)

CHANGING

IMPORTANT: Use only Mercury MerCruiser replacement parts to ensure compliance with

emission regulations.

NOTE: On V6 models the PCV valve is non‑serviceable and is an internal component of

the valve cover.

1. Remove the PCV valve from the port valve cover.

mc71925-1

a -

PCV valve

b -

Hose

2. Disconnect the PCV valve from the hose and discard the valve.
3. Install a new PCV valve in the valve cover and reconnect the hose.
4. Ensure the PCV valve is tightly seated in the valve cover.

Water‑Separating Fuel Filter (MPI)

Water‑Separating Fuel Filter

WARNING

Fuel is flammable and explosive. Ensure the key switch is off and the lanyard is positioned

so that the engine cannot start. Do not smoke or allow sources of spark or open flame in

the area while servicing. Keep the work area well ventilated and avoid prolonged

exposure to vapors. Always check for leaks before attempting to start the engine and

wipe up any spilled fuel immediately.

CAUTION

Failure to release pressure from the fuel system will result in fuel spraying out, which can

cause a fire or explosion. Allow the engine to cool completely and release all fuel pressure

before servicing any part of the fuel system. Always protect eyes and skin from

pressurized fuel and vapors.

Содержание 350 MAG MPI























































































































































Результаты поиска

Содержание 350 MAG MPI

Отзывы:

Похожие инструкции для 350 MAG MPI

Бренды по названию

Популярные бренды

MerCruiser 350 MAG MPI, Руководство пользователя

Результаты поиска

Содержание 350 MAG MPI

Отзывы:

Похожие инструкции для 350 MAG MPI

Бренды по названию

Популярные бренды