MerCruiser 350 MAG MPI Скачать руководство пользователя страница 53

Страница: 53 / 150

Section 3 - On The Water

90-864195070 JUNE 2007

Page 45

Operation Chart

BEFORE STARTING

AFTER STARTING

WHILE UNDERWAY

AFTER STOPPING

Operate bilge blowers.

Check steering operation.

Close seacock, if

equipped.

Open fuel shut off valve.

Flush cooling system if in

saltwater.

Open seacock, if

equipped.

Drain bilge.

Close the drain system.
Place sterndrive unit in

full down/in position.
Check the engine oil.
Perform all other checks

specified by your dealer

and/or boat builder.
Listen for Audio Warning

Alarm to sound when the

ignition switch is in the

"ON" position.

Starting and Stopping the Engine

NOTE: Only perform those functions applicable to your power package.

STARTING THE ENGINE

1. Check all items listed in the Operation Chart.
2. Place the remote control handle in neutral.

NOTICE

Failure to provide sufficient cooling water will damage the water pump and cause the

engine to overheat. Provide a sufficient supply of water at the water inlets during

operation.

WARNING

Explosive fumes contained in the engine compartment can cause serious injury or death

from fire or explosion. Before starting the engine, operate the bilge blower or vent the

engine compartment for at least five minutes.

3. Turn ignition key to "START". Release key when engine starts and allow switch to return

to "ON" position. Allow engine to warm up (6‑10 minutes on first start of the day).

4. If engine does not start after 3 attempts:

Push the

throttle only

button and position the remote control handle/throttle lever

to the 1/4 throttle position.

Turn ignition key to "START". Release key when engine starts and allow switch

to return to "ON" position.

5. If engine does not start after step 4:

Move the remote control handle/throttle lever to full throttle position, then return

to 1/4 throttle.

Turn ignition key to "START". Release key when engine starts and allow switch

to return to "ON" position.

6. Inspect the power package for fuel, oil, water and exhaust leaks.

Содержание 350 MAG MPI























































































































































Результаты поиска

Содержание 350 MAG MPI

Отзывы:

Похожие инструкции для 350 MAG MPI

Бренды по названию

Популярные бренды

MerCruiser 350 MAG MPI, Руководство пользователя

Результаты поиска

Содержание 350 MAG MPI

Отзывы:

Похожие инструкции для 350 MAG MPI

Бренды по названию

Популярные бренды