MerCruiser 350 MAG MPI Скачать руководство пользователя страница 125

Страница: 125 / 150

Section 6 - Storage

90-864195070 JUNE 2007

Page 117

NOTICE

Water trapped in the seawater section of the cooling system can cause corrosion or

freeze damage. Drain the seawater section of the cooling system immediately after

operation or before any length of storage in cold weather. If the boat is in the water, keep

the seacock closed until restarting the engine to prevent water from flowing back into the

cooling system. If the boat is not fitted with a seacock, leave the water inlet hose

disconnected and plugged.

9. Ensure that the sterndrive vent holes and water drain holes and passages are

unobstructed and open (refer to

Draining Instructions

10. For additional assurance against freezing and rust, after draining, fill the cooling system

with propylene glycol mixed to the manufacturer's recommendation to protect engine

to the lowest temperature to which it will be exposed during freezing temperatures or

extended storage.

NOTICE

The universal joint bellows may develop a set when stored in a raised or up position,

causing the bellows to fail when returned to service and allowing water to enter the boat.

Store the sterndrive in the full down position.

11. Store boat with drive unit in full down/in position.
12. Store the battery according to the manufacturer's instructions.

ENGINE AND FUEL SYSTEM PREPARATION

WARNING

Fuel is flammable and explosive. Ensure the key switch is off and the lanyard is positioned

so that the engine cannot start. Do not smoke or allow sources of spark or open flame in

the area while servicing. Keep the work area well ventilated and avoid prolonged

exposure to vapors. Always check for leaks before attempting to start the engine and

wipe up any spilled fuel immediately.

WARNING

Fuel vapors trapped in the engine compartment may be an irritant, cause difficulty

breathing, or may ignite resulting in a fire or explosion. Always ventilate the engine

compartment before servicing the power package.

1. In a 23 L (6 U.S. gal.) remote fuel tank mix:

19 L (5 U.S. gal) regular unleaded 87 octane (90 RON) gasoline

1.89 L (2 U.S. qts.) Premium Plus 2‑Cycle TC‑W3 Outboard Oil

150 mL (5 ounces) Fuel System Treatment and Stabilizer or 30 mL (1 ounce) Fuel

System Treatment and Stabilizer Concentrate

Tube Ref No.

Description

Where Used

Part No.

115

Premium Plus 2-cycle TC-W3

Outboard Oil

Fuel system

92-802824A1

124

Fuel System Treatment &

Stabilizer

Fuel system

802875A1

2. Allow the engine to cool down.
IMPORTANT: Immediately wipe up any fuel spills or sprays.

Содержание 350 MAG MPI























































































































































Результаты поиска

Содержание 350 MAG MPI

Отзывы:

Похожие инструкции для 350 MAG MPI

Бренды по названию

Популярные бренды

MerCruiser 350 MAG MPI, Руководство пользователя

Результаты поиска

Содержание 350 MAG MPI

Отзывы:

Похожие инструкции для 350 MAG MPI

Бренды по названию

Популярные бренды