MerCruiser 350 MAG MPI Скачать руководство пользователя страница 116

Страница: 116 / 150

Section 5 - Maintenance

Page 108

90-864195070 JUNE 2007

ALTERNATIVE WATER PICKUPS

IMPORTANT: Two water sources are needed for this procedure.

NOTE: Flushing is needed only for salty, brackish, mineral laden or polluted water

applications. Flushing is recommended after each outing for best results.

IMPORTANT: Engines with the sterndrive water inlet blocked off at the gimbal housing and

using a through‑hull water inlet need a supply of cooling water available to both the

sterndrive and to the engine during operation.
1. If flushing the cooling system with the boat in the water:

Raise sterndrive to trailer position.

Install the appropriate flushing attachment over the water inlet holes in the gear

housing.

Lower sterndrive unit to full down (in) position.

2. If flushing the cooling system with the boat out of the water:

Lower sterndrive to full down (in) position.

WARNING

Rotating propellers can cause serious injury or death. Never operate the boat out of the

water with a propeller installed. Before installing or removing a propeller, place the drive

unit in neutral and engage the lanyard stop switch to prevent the engine from starting.

Remove propeller.

Install the appropriate flushing attachment over the water inlet holes in the gear

housing.

3. Connect hose between flushing attachment and water source.
4. Close the seacock, if equipped, to prevent water from siphoning into the engine or boat.
5. Remove the seawater inlet hose from the seawater pump and plug the hose to prevent

water from siphoning into the engine or boat.

6147

6. Using a suitable adapter, connect the flushing hose from the water source to the water

inlet of the seawater pump.

NOTICE

Failure to provide sufficient cooling water will damage the water pump and cause the

engine to overheat. Provide a sufficient supply of water at the water inlets during

operation.

7. With sterndrive in normal operating position, open the water source fully.

Содержание 350 MAG MPI























































































































































Результаты поиска

Содержание 350 MAG MPI

Отзывы:

Похожие инструкции для 350 MAG MPI

Бренды по названию

Популярные бренды

MerCruiser 350 MAG MPI, Руководство пользователя

Результаты поиска

Содержание 350 MAG MPI

Отзывы:

Похожие инструкции для 350 MAG MPI

Бренды по названию

Популярные бренды