Meech AHU-CL1 Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 102

Meech AHU-CL1 Скачать руководство пользователя страница 61

AHU-CL1 Manual

Page

61

of

102

924IPS bars

The Hyperion 924 IPS is a compact pulsed DC ionising bar. It is used to control static electric charges in
short range applications (20-150mm). An integral 7.5kV pulsed DC power supply allows for easy
installation on printing, converting and packaging machinery. Requiring only a 24V DC supply, the 924
IPS removes the need to route high-voltage cabling through the machine.

On this system they come pre-assembled to the VacClean head. The installation is covered in the
beginning of the manual and in the electrical installation of the manual.

Operation

Having connected the M8 connector to the bar following the electrical installation, the bar will now
operate in line with the main AHU-CL1 so as the run signal is given to the AHU-CL1 the bars will turn on.
Check for a green constant LED on the bar. This indicates that the bar is running correctly with a good
ion output.

Caution

Always turn off the 24V supply (do not have the AHU-CL1 running) before connecting or disconnecting
the M8 connector. Failure to do so could result in stored charges giving a small electric shock.

Bar Master

A bar master is a control device for the 924IPS bars which allows the configuration of settings and
resetting of certain reference points.

The Bar master is not included with the system but can be requested for investigation into issues with
the 924IPS Bars.

All settings on the 924IPS bar are pre-set at Meech and are specifically designed for the install of this
system.

Figure 89 - BarMaster

«
...
59
60
61
62
63
...
»

Содержание AHU-CL1







































































































Отзывы:

Нет отзывов