manualshive.com logo in svg

Matsusada R4G Series, Инструкция по эксплуатации

Поделиться
Скачать
Matsusada R4G Series Скачать руководство пользователя страница 7

Table of Contents 

v 

R4G/R4GE series 

Table of Contents 

 

Page 

For Safe Use of the Product ............................................................................................................................................................................... i 
Table of Contents ..................................................................................................................................................................................................... v 

 

1 Introduction

 ··········································································································································································································· 1

 

1-1

 Introduction

 ·································································································································································································· 1

 

1-2

 Overview

 ······································································································································································································· 1

 

1-3

 Features

 ········································································································································································································ 1

 

1-4

 Lineup

 ············································································································································································································· 2

 

1-5

 Specifications

 ····························································································································································································· 3

 

 

2 Before Use

 ············································································································································································································ 5

 

2-1

 Unpacking

 ···································································································································································································· 5

 

2-2

 Initial Inspection

 ························································································································································································ 5

 

2-3

 Precautions for handling

 ······································································································································································· 5

 

2-4

 Installation

 ···································································································································································································· 6

 

2-4-1

 Installation Conditions

 ·································································································································································· 6

 

2-5

 External View

 ······························································································································································································ 7

 

2-5-1

 Front Panel

 ························································································································································································ 7

 

2-5-2

 Rear Panel

 ························································································································································································· 8

 

2-6

 External Dimensions (Unit: mm):

 ····················································································································································· 9

 

2-6-1

 Width: 84 mm

 ···················································································································································································· 9

 

2-6-2

 Width: 105 mm

 ·············································································································································································· 10

 

2-6-3

 Width: 210 mm

 ·············································································································································································· 11

 

2-7

 Remote Interface Connector (TB1) and Function Setting Switch (SW1)

 ································································· 12

 

2-7-1

 Remote Interface Connector (TB1)

 ···································································································································· 12

 

2-7-2

 Function Setting Switch (SW1)

 ············································································································································· 13

 

2-8

 When Connecting a Load with Accumulated Energy

 ········································································································· 13

 

 

3 Basic Operation to Output

 ·········································································································································································· 14

 

 

4 Normal Operation

 ··························································································································································································· 15

 

4-1

 Operating Mode Description

 ···························································································································································· 15

 

4-1-1

 Constant Voltage (CV) Mode

 ················································································································································ 15

 

4-1-2

 Constant Current (CC) Mode

 ················································································································································ 15

 

4-1-3

 Crossover Mode

 ··········································································································································································· 15

 

4-2

 Output ON/OFF

 ······················································································································································································ 16

 

4-3

 Presetting the Output Voltage and Output Current

 ·············································································································· 16

 

4-4

 OVP (Overvoltage Protection) and OCP (Overcurrent Protection)

 ············································································· 16

 

4-5

 LOCK

 ··········································································································································································································· 19

 

4-6

 Power Failure Protection

 ··································································································································································· 20

 

4-7

 Last Setting Memory

 ············································································································································································ 20

 

4-8

 -LS (Remote Switch) ON/OFF (only for R4G series)

 ·········································································································· 21

 

4-9

 -LD (Interlock) (only for R4G series)

 ··········································································································································· 23

 

4-10

 Remote Sensing (only for R4G series)

 ···································································································································· 24

 

4-11

 Error List

 ·································································································································································································· 24

 

 

Содержание R4G Series





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды