Matsusada R4G Series Скачать руководство пользователя страница 21

Страница: 21 / 60

R4G/R4GE series

2-7-2

Function Setting Switch (SW1)

SW1-1

Do not use

SW1-2

Do not use

SW1-3

Do not use

SW1-4

Do not use

SW1-5

Current program switching
(OFF: External voltage, ON: External resistance)

SW1-6

Current local/remote mode switching
(OFF: Remote, ON: Local)

SW1-7

Voltage program switching
(OFF: External voltage, ON: External resistance)

SW1-8

Voltage local/remote mode switching (OFF: Remote, ON: Local)

2-8

When Connecting a Load with Accumulated Energy

When a load with accumulated energy such as a battery is connected, current flows from the load to the

internal circuitry of the unit. Therefore, the unit can be a malfunction, and/or the load's life might be

affected.

When connecting to such a load, be sure to connect a diode in series as protection against reverse

current between the unit and the load, as shown in the diagram below.



Select a diode to protect the unit and load from reverse current based on the following criteria.

1.  Rated reverse voltage resistance: two times or higher than the rated output voltage of the unit
2.  Forward current capacity: three to ten times the rated output current of the unit
3.  Less loss



Consider the heat generated by the diode. If the heat dissipation is insufficient, the diode will burn
out



It cannot be used together with the remote sensing function.

Load with accumulated energy
(Battery or capacitor)

P.S.

SW1

8
7
6
5
4
3
2
1

Содержание R4G Series





























































Результаты поиска

Содержание R4G Series

Отзывы:

Бренды по названию

Популярные бренды

Matsusada R4G Series, Инструкция по эксплуатации

Результаты поиска

Содержание R4G Series

Отзывы:

Бренды по названию

Популярные бренды