manualshive.com logo in svg

Matsusada R4G Series, Инструкция по эксплуатации

Поделиться
Скачать
Matsusada R4G Series Скачать руководство пользователя страница 6

 

iv 

R4G/R4GE series 

 

 

 

Level the product out to use for good heat dissipation. 

Do not install the product upside down or sideways. If not, the inner heat dissipation will be insufficient. 
It may result in smoke or fire due to components deterioration. 
 

 

Do not install the product in a place where cold air directly blows to it. 

It may result in electric leakage or burnout due to condensation. 
 

 

Do not install the product in a place where it is exposed to corrosive gases or liquids. 

It may result in smoke or burnout due to components deterioration. 
 

 

Do not store or use the product in a place where conductive dust, such as iron power, can enter 
through the air inlet/outlet.

 

Doing so may cause a short circuit, resulting in electric leakage, burnout, fire, or malfunction. 
 

 

Do not install the product in a dusty place. 

Accumulating dust in the air inlet will make hard to cool it down it, it may result in malfunction. 
In that case, remove dust immediately. 
 

 

Do not block the air inlet and outlet. 

Secure 30 cm space at least around the openings. 
If  they  are  blocked,  the  product  cannot  show  the  rated  performance  due  to  the  internal  temperature 
increase. Moreover, components deteriorate and it may result in smoke or fire. 
 

 

Remove wiring to and from the product when work like welding near it is done. 

 

 

Do not wipe the equipment with a dust cloth wet with chemicals (thinner or the like) or water.   

Otherwise, it may result in an electric shock, electric leakage, or burnout due to water getting inside. 
 

 

Regarding fan replacement 

When products equip a fan, it has a lifetime. It will be worn out and deteriorated with the time passed and 
its operation may become unstable. Also, its lifetime greatly varies depending on the usage environment 
such as temperature, humidity, dust. It requires to be replaced at regular intervals to extend the lifetime. 
For the replacement, contact us. 
(It  requires  a replacement charge separately.  Do not  replace it  by yourself, as  there is a risk of  electric 
shock.) 

 
 
 

Содержание R4G Series





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды